参数资料
| 型号： | TISP4070L3BJR-S |
| 厂商： | Bourns Inc. |
| 文件页数： | 6/13页 |
| 文件大小： | 0K |
| 描述： | PROTECTOR SINGLE BIDIRECTIONAL |
| 标准包装： | 3,000 |
| 电压 - 击穿： | 70V |
| 电压 - 断路： | 58V |
| 电压 - 导通状态： | 3V |
| 电流 - 峰值脉冲(8 x 20µs)： | 300A |
| 电流 - 保持 (Ih)： | 120mA |
| 元件数： | 1 |
| 电容： | 48pF |
| 封装/外壳： | DO-214AA，SMB |
| 包装： | 带卷 (TR) |
TISP4xxxL3BJ Overvoltage Protector Series
APPLICATIONS INFORMATION
FCC Part 68, ACTA, TIA and EIA
From 2001, the registrations for FCC equipment changed from the FCC to ACTA, Administrative Council for Terminal Attachments. For this
function, ACTA needed to adopt a US National standard specifying terminal equipment requirements. The TIA, Telecommunications Industry
Association, in conjunction with the EIA, Electronic Industries Alliance, created TIA/EIA-IS-968 for this purpose. The first issue of TIA/EIA-IS-968
is essentially a renumbered version of the FCC Part 68 requirement. Clause and figure changes are shown in the table.
Item
Telephone Line Surge – Type A
FCC Part 68 TIA/EIA-IS-968
Clause 68.302 (b) Clause 4.2.2
Telephone Line Surge – Type B
Simplified Surge Generator
Open Circuit voltage Wave shape
Short Circuit Current Wave shape
Clause 68.302 (c)
Fig. 68.302 (a)
Fig. 68.302 (b)
Fig. 68.302 (c)
Clause 4.2.3
Figure 4.1
Figure 4.2
Figure 4.3
TIA/EIA-IS-968 (FCC Part 68) Impulse Testing
To verify the withstand capability and safety of the equipment, standards require that the equipment is tested with various impulse wave forms.
The table below shows values for the TIA/EIA-IS-968 and ITU-T recommendation K.21.
Test
Peak
Voltage
Peak
Current
Fictive
TISP4xxxL3
Series
Standard
TIA/EIA-IS-968
(F CC Part 68)
ITU-T K.21 ?
Basic Level
ITU-T K.21 ?
Enhanced Level
Condition
V
Longitudinal
Metallic
Longitudinal
Metallic
Transverse
Transverse
Voltage
V
1500
800
1500
1000
1500
4000
1500
6000
Wave Form
μ s
10/160
10/560
9/720 ?
9/720 ?
10/700
10/700
Current
A
200
100
37.5
25
37.5
100
37.5
125
Wave Form
μ s
10/160
10/560
5/320 ?
5/320 ?
5/310
5/310
Impedance
?
7.5
8
40
40
40
40
Rating
A
50
30
40
40
30
30
Resistance
?
2 x 24
19
0
0
0
10
0
10
? TIA/EIA-IS-968 terminology for the wave forms produced by the ITU-T recommendation K.21 10/700 impulse generator
? Values assume the TISP4xxxL3 is connected inter-conductor and a 400 V primary is used
If the impulse generator current exceeds the protector’s current rating then a series resistance can be used to reduce the current to the
protector’s rated value to prevent possible failure. The required value of series resistance for a given wave form is given by the following
calculations. First, the minimum total circuit impedance is found by dividing the impulse generator’s peak voltage by the protector’s rated
current. The impulse generator’s fictive impedance (generator ’s peak voltage divided by peak short circuit current) is then subtracted from the
minimum total circuit impedance to give the required value of series resistance.
For the TIA/EIA-IS-968 10/560 wave form the following values result. The minimum total circuit impedance is 800/30 = 26.7 ? and the
generator ’s fictive impedance is 800/100 = 8 ? . For an inter-conductor connected TISP4xxxL3, this gives a minimum series resistance value of
26.7 - 8 = 18.7 ? . After allowing for tolerance, a 20 ? ± 5 % resistor would be suitable. The 10/160 wave form only needs to be considered if
the TISP4350L3 is connected from the conductor to ground. In this case, the conductor series resistance is 24 ? ± 5 % per conductor.
IEC 60950, UL 1950/60950, CSA C22.2 No. 950/60950 and EN 60950
These electrical safety standards for IT (Information Technology) equipment at the customer premise use the IEC (International Electro-
technical Commission) 60950 standard as the core document. The IEC 60950 covers fundamental safety criteria such as creepage and
isolation. The connection to a telecommunication network voltage (TNV) is covered in clause 6.
Europe is harmonized by CENELEC (Comité Européen de Normalization Electro-technique) under EN 60950 (included in the Low Voltage
Directive, CE mark). Up to the end of 2000, the US had UL (Underwriters Laboratories) 1950 and Canada CSA (Canadian Standards Authority)
C22.2 No. 950. The US and Canadian standards include regional changes and additions to the IEC 60950. A major addition is the inclusion of
clause 6.6, power cross withstand containing the flowchart Figure 18b and annex NAC covering testing. Remarks made for UL 1950 will
generally be true for CSA 22.2 No. 950.
AUGUST 1999 - REVISED JANUARY 2007
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
相关PDF资料 |
PDF描述 |
|---|---|
| 929500-01-29 | CONN HEADER .100 SNGL R/A 29POS |
| 1.5KE24A-E3/54 | TVS UNIDIR 1.5KW 24V 5% 1.5KE |
| 929834-07-16 | CONN HEADER .100 SNGL STR 16POS |
| SSQ-117-01-G-S | CONN RCPT .100" 17POS SNGL GOLD |
| PEC04DBEN | CONN HEADER .100 DUAL R/A 8POS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TISP4070L3LM | 制造商:BOURNS 制造商全称:Bourns Electronic Solutions 功能描述:BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS |
| TISP4070L3LM-S | 功能描述:硅对称二端开关元件 Single bidirectional protector RoHS:否 制造商:Bourns 转折电流 VBO:40 V 最大转折电流 IBO:800 mA 不重复通态电流: 额定重复关闭状态电压 VDRM:25 V 关闭状态漏泄电流（在 VDRM IDRM 下）: 保持电流（Ih 最大值）:50 mA 开启状态电压:5 V 关闭状态电容 CO:120 pF 最大工作温度:+ 150 C 安装风格:SMD/SMT 封装 / 箱体:DO-214AA |
| TISP4070M3AJ | 制造商:BOURNS 制造商全称:Bourns Electronic Solutions 功能描述:BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS |
| TISP4070M3AJR | 功能描述:硅对称二端开关元件 RoHS:否 制造商:Bourns 转折电流 VBO:40 V 最大转折电流 IBO:800 mA 不重复通态电流: 额定重复关闭状态电压 VDRM:25 V 关闭状态漏泄电流（在 VDRM IDRM 下）: 保持电流（Ih 最大值）:50 mA 开启状态电压:5 V 关闭状态电容 CO:120 pF 最大工作温度:+ 150 C 安装风格:SMD/SMT 封装 / 箱体:DO-214AA |
| TISP4070M3AJR-S | 功能描述:硅对称二端开关元件 BIDIRECTIONAL PRTCTR 58volts RoHS:否 制造商:Bourns 转折电流 VBO:40 V 最大转折电流 IBO:800 mA 不重复通态电流: 额定重复关闭状态电压 VDRM:25 V 关闭状态漏泄电流（在 VDRM IDRM 下）: 保持电流（Ih 最大值）:50 mA 开启状态电压:5 V 关闭状态电容 CO:120 pF 最大工作温度:+ 150 C 安装风格:SMD/SMT 封装 / 箱体:DO-214AA |
发布紧急采购，3分钟左右您将得到回复。