参数资料
| 型号： | TISP4070L3BJR |
| 厂商： | Bourns Inc. |
| 文件页数： | 11/13页 |
| 文件大小： | 0K |
| 描述： | SURGE SUPP 58V BIDIR DO-214AA |
| 标准包装： | 3,000 |
| 电压 - 击穿： | 70V |
| 电压 - 断路： | 58V |
| 电压 - 导通状态： | 3V |
| 电流 - 峰值脉冲(8 x 20µs)： | 300A |
| 电流 - 保持 (Ih)： | 120mA |
| 元件数： | 1 |
| 电容： | 48pF |
| 封装/外壳： | DO-214AA，SMB |
| 包装： | 带卷 (TR) |
TISP4xxxL3BJ Overvoltage Protector Series
APPLICATIONS INFORMATION
TISP4xxxL3BJ and UL 60950 Power Cross
The TISP4xxxL3BJ conducts current for periods greater than the power cross test times, Figure 2, so the TISP4xxxL3BJ is not a major factor
in UL 60950 compliance. The main design task for UL 60950 power cross is about enclosure design and the selection of the other components
that are subject to power cross. A UL specified fuse together with a TISP4xxxL3BJ gives a simple approach to meeting the power cross
requirements.
Fuse Values
There are two areas of fuse criteria; surge capability (TIA/EIA-IS-968 (FCC Part 68) impulse) and power cross capability (UL60950 clause 6.4
and annex NAC).
To survive an impulse, a fuse must have a melting I2t rating greater than the impulse I2t. The fuse I2t rating should be specified for the impulse
waveshape current as the normal d.c. rating may not result in adiabatic conditions. Alternatively, the fuse may be specified for a rated current
under the impulse waveshape conditions.
An exponentially decaying impulse with a current amplitude IPP and 50 % amplitude decay time of t D has an I 2t value of 0.72 IPP 2tD.
Test waveforms have tolerances and the formula can be approximated to IPP2tD, giving about a 40 % allowance to cover tolerances, e.g.
+5 % on IPP and +30 % on tD. Using the approximate formula, the I2t values for typical waveforms are shown in the table below.
Specification
TIA/EIA-IS-968 Type A (FCC Part 68)
TIA/EIA-IS-968 Type B (FCC Part 68)
UL 60950 / ITU-T K.21
Telcordia (formally Bellcore)
GR-1089-CORE
Amplitude I PP
A
200
100
37.5
37.5
500
100
Current Wave Shape
t R / t D ( μ s)
10/160
10/560
5/320
5/310
2/10
10/1000
Melting I 2 t
A 2 s
6.4
5.6
0.45
0.45
2.5
10
UL 60950, Annex NAC testing requires that the total I 2 t does not exceed 100 A 2 s for test 1
K.21 has a.c. induction withstand tests of 1 A 2 s (basic) and 10 A 2 s (enhanced)
Fuse power cross current capability can be determined from its time-current curve. The fuse must be rated to break the current at the applied
power cross a.c. voltage level.
Fuses for TIA/EIA-IS-968
To survive both the Type A surges, a fuse I 2 t value of greater than 6.4 A 2 s is needed. Fuses such as the Bel SMP 1.25 will meet this criteria and
they are rated for 60 A, 600 V a.c. interruption.
Fuses must not operate on the Type B surge. To survive a 37.5 A Type B surge, the fuse needs to have an I 2 t of greater than 0.45 A 2 s. A non-
operational pass for TIA/EIA-IS-968 Type A impulses is allowed; this could be a design approach with the TISP4xxxL3, which is likely to fail
short with Type A impulses. A fuse with an I 2 t greater than 0.45 A 2 s and less than 5.6 A 2 s would be needed to ensure that the resultant Type A
impulse fault mode disconnects the modem from the line (avoiding a permanent off-hook condition). The Bel SMP 500 fuse starts to operate at
60 % of the specified Type A impulse current levels and is rated for 60 A, 600 V a.c. interruption.
Fuses for ITU-T Recommendation K.21
Like TIA/EIA-IS-968, K.21 requires an operation pass on a 37.5 A, 5/310 transverse current impulse, giving a minimum fuse I 2 t of 0.45 A 2 s. This
value may be increased when the coordination test requirements are included. Depending on the conformance level, basic or enhanced, an
a.c. power induction operational pass requires a minimum fuse I 2 t of either a 1 A 2 s or a 10 A 2 s level.
AUGUST 1999 - REVISED JANUARY 2007
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
相关PDF资料 |
PDF描述 |
|---|---|
| PEC24DBAN | CONN HEADER .100 DUAL R/A 48POS |
| PBC13DFBN | CONN HEADER .100 DUAL STR 26POS |
| PBC06DAGN | CONN HEADER .100 DUAL STR 12POS |
| PBC10DADN | CONN HEADER .100 DUAL STR 20POS |
| 794621-6 | CONN HEADER 6POS DL R/A TIN SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TISP4070L3BJR-S | 功能描述:硅对称二端开关元件 PROTECTOR - SINGLE BIDIRECTIONAL RoHS:否 制造商:Bourns 转折电流 VBO:40 V 最大转折电流 IBO:800 mA 不重复通态电流: 额定重复关闭状态电压 VDRM:25 V 关闭状态漏泄电流（在 VDRM IDRM 下）: 保持电流（Ih 最大值）:50 mA 开启状态电压:5 V 关闭状态电容 CO:120 pF 最大工作温度:+ 150 C 安装风格:SMD/SMT 封装 / 箱体:DO-214AA |
| TISP4070L3LM | 制造商:BOURNS 制造商全称:Bourns Electronic Solutions 功能描述:BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS |
| TISP4070L3LM-S | 功能描述:硅对称二端开关元件 Single bidirectional protector RoHS:否 制造商:Bourns 转折电流 VBO:40 V 最大转折电流 IBO:800 mA 不重复通态电流: 额定重复关闭状态电压 VDRM:25 V 关闭状态漏泄电流（在 VDRM IDRM 下）: 保持电流（Ih 最大值）:50 mA 开启状态电压:5 V 关闭状态电容 CO:120 pF 最大工作温度:+ 150 C 安装风格:SMD/SMT 封装 / 箱体:DO-214AA |
| TISP4070M3AJ | 制造商:BOURNS 制造商全称:Bourns Electronic Solutions 功能描述:BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS |
| TISP4070M3AJR | 功能描述:硅对称二端开关元件 RoHS:否 制造商:Bourns 转折电流 VBO:40 V 最大转折电流 IBO:800 mA 不重复通态电流: 额定重复关闭状态电压 VDRM:25 V 关闭状态漏泄电流（在 VDRM IDRM 下）: 保持电流（Ih 最大值）:50 mA 开启状态电压:5 V 关闭状态电容 CO:120 pF 最大工作温度:+ 150 C 安装风格:SMD/SMT 封装 / 箱体:DO-214AA |
发布紧急采购，3分钟左右您将得到回复。