- 您现在的位置：买卖IC网 > PDF目录225308 > TISP4395H3LM (BOURNS INC) 395 V, 60 A, SILICON SURGE PROTECTOR, DO-92 PDF资料下载
参数资料
| 型号： | TISP4395H3LM |
| 厂商： | BOURNS INC |
| 元件分类： | 浪涌电流限制器 |
| 英文描述： | 395 V, 60 A, SILICON SURGE PROTECTOR, DO-92 |
| 封装： | PLASTIC, TO-92, 2 PIN |
| 文件页数： | 3/13页 |
| 文件大小： | 376K |
| 代理商： | TISP4395H3LM |
NOVEMBER 1997 - REVISED JANUARY 2007
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
Capacitance
TISP4xxxH3LM Overvoltage Protector Series
APPLICATIONS INFORMATION
The protector characteristic off-state capacitance values are given for d.c. bias voltage, VD, values of 0, -1 V, -2 V and -50 V. Where possible,
values are also given for -100 V. Values for other voltages may be calculated by multiplying the VD = 0 capacitance value by the factor given in
Figure 6. Up to 10 MHz, the capacitance is essentially independent of frequency. Above 10 MHz, the effective capacitance is strongly
dependent on connection inductance. In many applications, such as Figure 15 and Figure 17, the typical conductor bias voltages will be about
-2 V and -50 V. Figure 7 shows the differential (line unbalance) capacitance caused by biasing one protector at -2 V and the other at -50 V.
Normal System Voltage Levels
The protector should not clip or limit the voltages that occur in normal system operation. For unusual conditions, such as ringing without the
line connected, some degree of clipping is permissible. Under this condition, about 10 V of clipping is normally possible without activating the
ring trip circuit.
Figure 10 allows the calculation of the protector VDRM value at temperatures below 25 °C. The calculated value should not be less than the
maximum normal system voltages. The TISP4260H3LM, with a VDRM of 200 V, can be used for the protection of ring generators producing
100 V rms of ring on a battery voltage of -58 V (Th2 and Th3 in Figure 17). The peak ring voltage will be 58 + 1.414*100 = 199.4 V. However,
this is the open circuit voltage and the connection of the line and its equipment will reduce the peak voltage. In the extreme case of an
unconnected line, clipping the peak voltage to 190 V should not activate the ring trip. This level of clipping would occur at the temperature
when the VDRM has reduced to 190/200 = 0.95 of its 25 °C value. Figure 10 shows that this condition will occur at an ambient temperature of
-22 °C. In this example, the TISP4260H3LM will allow normal equipment operation provided that the minimum expected ambient
temperature does not fall below -22 °C.
JESD51 Thermal Measurement Method
To standardize thermal measurements, the EIA (Electronic Industries Alliance) has created the JESD51 standard. Part 2 of the standard
(JESD51-2, 1995) describes the test environment. This is a 0.0283 m3 (1 ft 3) cube which contains the test PCB (Printed Circuit Board)
horizontally mounted at the center. Part 3 of the standard (JESD51-3, 1996) defines two test PCBs for surface mount components; one for
packages smaller than 27 mm (1.06 ’’) on a side and the other for packages up to 48 mm (1.89 ’’). The LM package measurements used the
smaller 76.2 mm x 114.3 mm (3.0 ’’ x 4.5 ’’) PCB. The JESD51-3 PCBs are designed to have low effective thermal conductivity (high thermal
resistance) and represent a worse case condition. The PCBs used in the majority of applications will achieve lower values of thermal resistance
and so can dissipate higher power levels than indicated by the JESD51 values.
相关PDF资料 |
PDF描述 |
|---|---|
| TISP4400H3LMFR | 400 V, 60 A, SILICON SURGE PROTECTOR, DO-92 |
| TISP4400H3LM | 400 V, 60 A, SILICON SURGE PROTECTOR, DO-92 |
| TISP4220M3LM | 220 V, 32 A, SILICON SURGE PROTECTOR, DO-92 |
| TISP4240M3LM | 240 V, 32 A, SILICON SURGE PROTECTOR, DO-92 |
| TISP4400M3LM | 400 V, 32 A, SILICON SURGE PROTECTOR, DO-92 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TISP4395H3LMFR | 功能描述:硅对称二端开关元件 RoHS:否 制造商:Bourns 转折电流 VBO:40 V 最大转折电流 IBO:800 mA 不重复通态电流: 额定重复关闭状态电压 VDRM:25 V 关闭状态漏泄电流（在 VDRM IDRM 下）: 保持电流（Ih 最大值）:50 mA 开启状态电压:5 V 关闭状态电容 CO:120 pF 最大工作温度:+ 150 C 安装风格:SMD/SMT 封装 / 箱体:DO-214AA |
| TISP4395H3LMFR-S | 功能描述:硅对称二端开关元件 PROTECTOR - SINGLE BIDIRECTIONAL RoHS:否 制造商:Bourns 转折电流 VBO:40 V 最大转折电流 IBO:800 mA 不重复通态电流: 额定重复关闭状态电压 VDRM:25 V 关闭状态漏泄电流（在 VDRM IDRM 下）: 保持电流（Ih 最大值）:50 mA 开启状态电压:5 V 关闭状态电容 CO:120 pF 最大工作温度:+ 150 C 安装风格:SMD/SMT 封装 / 箱体:DO-214AA |
| TISP4395H3LM-S | 功能描述:硅对称二端开关元件 Single bidirectional protector RoHS:否 制造商:Bourns 转折电流 VBO:40 V 最大转折电流 IBO:800 mA 不重复通态电流: 额定重复关闭状态电压 VDRM:25 V 关闭状态漏泄电流（在 VDRM IDRM 下）: 保持电流（Ih 最大值）:50 mA 开启状态电压:5 V 关闭状态电容 CO:120 pF 最大工作温度:+ 150 C 安装风格:SMD/SMT 封装 / 箱体:DO-214AA |
| TISP4395J1 | 制造商:BOURNS 制造商全称:Bourns Electronic Solutions 功能描述:BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS |
| TISP4395J1BJ | 制造商:BOURNS 制造商全称:Bourns Electronic Solutions 功能描述:BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS |
发布紧急采购，3分钟左右您将得到回复。