- 您现在的位置：买卖IC网 > PDF目录372454 > TISP61089BDR (Electronic Theatre Controls, Inc.) TISP61089B High Voltage Ringing SLIC Protector PDF资料下载
参数资料
| 型号： | TISP61089BDR |
| 厂商： | Electronic Theatre Controls, Inc. |
| 英文描述： | TISP61089B High Voltage Ringing SLIC Protector |
| 中文描述： | TISP61089B高压振铃用户接口保护 |
| 文件页数： | 6/22页 |
| 文件大小： | 411K |
| 代理商： | TISP61089BDR |
OCTOBER 2000 - REVISED FEBRUARY 2005
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
TISP61089B High Voltage Ringing SLIC Protector
APPLICATIONS INFORMATION
Operation of Ringing SLICs using Multiple Negative Voltage Supply Rails
Figure 4 shows a typical powering arrangement for a multi-supply rail SLIC. VBATL is a lower (smaller) voltage supply than VBATH. With supply
switch S1 in the position shown, the line driver amplifiers are powered between 0 V and VBATL. This mode minimizes the power consumption
for short loop transmission. For long loops and to generate ringing, the driver voltage is increased by operating S1 to connect VBATH. These
conditions are shown in Figure 5.
SLIC
Figure 4. SLIC with Voltage Supply Switching
S1
LINE
DRIVERS
V
BATH
0 V
AI6XCC
SUPPLY
SWITCH
LINE
V
BATL
Figure 5. Driver Supply Voltage Levels
0 V
0 V
V
BATL
SHORT LOOP
V
BATH
LONG LOOP
V
DCRING
V
SLICG
V
PKRING
/2
V
SLICH
AI6XCD
V
BATH
V
BATH
RINGING
V
PKRING
/2
V
PKRING
/2
V
PKRING
/2
0 V
Conventional ringing is typically unbalanced ground or battery backed. To minimize the supply voltage required, most multi-rail SLICs use
balanced ringing as shown in Figure 5. The ringing has d.c., V
DCRING
, and a.c., V
PKRING
, components. A 70 V r.m.s. a.c. sinusoidal ring signal
has a peak value, V
PKRING
, of 99 V. If the d.c. component was 20 V, then the total voltage swing needed would be 99 + 20 = 119 V. There are
internal losses in the SLIC from ground, V
SLICG
, and the negative supply, V
SLICH
. The sum of these two losses generally amounts to a total of
10 V. This makes a total, V
BATH
, supply rail value of 119 + 10 = 129 V.
In some cases a trapezoidal a.c. ring signal is used. This would have a peak to r.m.s ratio (crest factor) of about 1.25, increasing the r.m.s. a.c.
ring level by 13 %. The d.c. ring voltage may be lowered for short loop applications.
相关PDF资料 |
PDF描述 |
|---|---|
| TISP61089BD-S | TISP61089B High Voltage Ringing SLIC Protector |
| TISP61089BDR-S | TISP61089B High Voltage Ringing SLIC Protector |
| TISP6L7591 | DUAL FORWARD-CONDUCTING P-GATE THYRISTORS PROGRAMMABLE OVERVOLTAGE PROTECTORS |
| TISP6L7591DR-S | DUAL FORWARD-CONDUCTING P-GATE THYRISTORS PROGRAMMABLE OVERVOLTAGE PROTECTORS |
| TISP6L7591DR | DUAL FORWARD-CONDUCTING P-GATE THYRISTORS PROGRAMMABLE OVERVOLTAGE PROTECTORS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TISP61089BDR-S | 功能描述:SCR Dual P Gate Forward Conducting RoHS:否 制造商:STMicroelectronics 最大转折电流 IBO:480 A 额定重复关闭状态电压 VDRM:600 V 关闭状态漏泄电流（在 VDRM IDRM 下）:5 uA 开启状态 RMS 电流 (It RMS): 正向电压下降:1.6 V 栅触发电压 (Vgt):1.3 V 最大栅极峰值反向电压:5 V 栅触发电流 (Igt):35 mA 保持电流（Ih 最大值）:75 mA 安装风格:Through Hole 封装 / 箱体:TO-220 封装:Tube |
| TISP61089BDR-T | 功能描述:SCR PROTECTOR - PROGRAMMABLE SLIC PROTECT RoHS:否 制造商:STMicroelectronics 最大转折电流 IBO:480 A 额定重复关闭状态电压 VDRM:600 V 关闭状态漏泄电流（在 VDRM IDRM 下）:5 uA 开启状态 RMS 电流 (It RMS): 正向电压下降:1.6 V 栅触发电压 (Vgt):1.3 V 最大栅极峰值反向电压:5 V 栅触发电流 (Igt):35 mA 保持电流（Ih 最大值）:75 mA 安装风格:Through Hole 封装 / 箱体:TO-220 封装:Tube |
| TISP61089BDS | 制造商:Bourns Inc 功能描述: |
| TISP61089BD-S | 功能描述:SCR Dual P Gate Forward Conducting RoHS:否 制造商:STMicroelectronics 最大转折电流 IBO:480 A 额定重复关闭状态电压 VDRM:600 V 关闭状态漏泄电流（在 VDRM IDRM 下）:5 uA 开启状态 RMS 电流 (It RMS): 正向电压下降:1.6 V 栅触发电压 (Vgt):1.3 V 最大栅极峰值反向电压:5 V 栅触发电流 (Igt):35 mA 保持电流（Ih 最大值）:75 mA 安装风格:Through Hole 封装 / 箱体:TO-220 封装:Tube |
| TISP61089BGDR-S | 功能描述:PROTECTOR PROGRAMMABLE SLIC RoHS:是 类别:过电压，电流，温度装置 >> TVS - 晶闸管 系列:- 产品变化通告:Product Discontinuation 19/Jul/2012 标准包装:2,500 系列:- 电压 - 击穿:400V 电压 - 断路:320V 电压 - 导通状态:4V 电流 - 峰值脉冲(8 x 20µs):250A 电流 - 峰值脉冲(10 x 1000µs):80A 电流 - 保持 (Ih):150mA 元件数:1 电容:29pF 封装/外壳:DO-214AA，SMB 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。