参数资料
| 型号： | TISP7180F3SL |
| 厂商： | Bourns Inc. |
| 文件页数： | 17/19页 |
| 文件大小： | 0K |
| 描述： | SURGE SUPP 145V BIDIR 3-SL |
| 产品变化通告： | Product Obsolescence Jun/2008 |
| 标准包装： | 50 |
| 电压 - 击穿： | 180V |
| 电压 - 断路： | 145V |
| 电压 - 导通状态： | 5V |
| 电流 - 峰值脉冲(8 x 20µs)： | 175A |
| 电流 - 峰值脉冲(10 x 1000µs)： | 45A |
| 电流 - 保持 (Ih)： | 150mA |
| 元件数： | 3 |
| 电容： | 47pF |
| 封装/外壳： | 径向 - 3 引线 |
| 包装： | 管件 |
TISP7xxxF3 (MV, HV) Overvoltage Protector Series
APPLICATIONS INFORMATION
Lightning Surge (continued)
1.2/50 Generators (continued)
C 4
8 nF
V C
1 kV
SW
R 2
13 ?
C 3
8 nF
NOTE: SOME STANDARDS
REPLACE OUTPUT
C 1
1 μ F
R 1
76 ?
C 2
30 nF
CAPACITORS WITH
25 ? RESISTORS
K.22 1.2/50 GENERATOR
Figure 34.
There are 8/20 short circuit current defined generators. These are usually very high current, 10 kA or more and are used for testing a.c.
protectors, primary protection modules and some Gas Discharge Tubes.
Impulse Testing
To verify the withstand capability and safety of the equipment, standards require that the equipment is tested with various impulse wave forms.
The table in this section shows some common test values.
Manufacturers are being increasingly required to design in protection coordination. This means that each protector is operated at its design
level and currents are diverted through the appropriate protector, e.g. the primary level current through the primary protector and lower levels
of current may be diverted through the secondary or inherent equipment protection. Without coordination, primary level currents could pass
through the equipment only designed to pass secondary level currents. To ensure coordination happens with fixed voltage protectors, some
resistance is normally used between the primary and secondary protection (R1a and R1b, Figure 36). The values given in this data sheet apply
to a 400 V (d.c. sparkover) gas discharge tube primary protector and the appropriate test voltage when the equipment is tested with a primary
protector.
Peak Voltage
Voltage
Peak Current
Current
TISP7xxxF3
Series
Coordination
Standard
Setting
V
Waveform
μ s
Value
A
Waveform
μ s
25 ° C Rating
A
Resistance
?
Resistance
? (Min.)
GR-1089-CORE
2500 2/10 2 x 500 2/10 2 x 190
1000 10/1000 2 x 100 10/1000 2 x 45
12
NA
1500 10/160 200 10/160 110 6
FCC Part 68
(March 1998)
800 10/560 100 10/560 50 8
1000 9/720 ? 25 5/320 ? 70
1500 (SINGLE) 37.5 5/320 ? 70 0
NA
1500
(DUAL)
2 x 27
4/250
2 x 95
I 31-24 1500 0.5/700 37.5 0.2/310 70 0
NA
1000
10/700
25
5/310
70
0
NA
ITU-T K.20/K.21
1500
4000
4000
(SINGLE)
(SINGLE)
(DUAL)
37.5
100
2 x 72
5/310
5/310
4/250
70
70
2 x 95
0
17
0
NA
6
6
? FCC Part 68 terminology for the waveforms produced by the ITU-T recommendation K.21 10/700 impulse generator
NA = Not Applicable, primary protection removed or not specified.
If the impulse generator current exceeds the protector ’s current rating, then a series resistance can be used to reduce the current to the
protector ’s rated value to prevent possible failure. The required value of series resistance for a given waveform is given by the following
calculations. First, the minimum total circuit impedance is found by dividing the impulse generator ’s peak voltage by the protector ’s rated
current. The impulse generator ’s fictive impedance (generator’s peak voltage divided by peak short circuit current) is then subtracted from the
minimum total circuit impedance to give the required value of series resistance. In some cases, the equipment will require verification over a
temperature range. By using the derated waveform values from the thermal information section, the appropriate series resistor value can be
calculated for ambient temperatures in the range of 0 ° C to 70 ° C.
MARCH 1994 - REVISED SEPTEMBER 2008
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
相关PDF资料 |
PDF描述 |
|---|---|
| 104354-3 | CONN HDR BRKWAY 6POS R/A DUAL |
| PEC23SGBN | CONN HEADER .100 SINGL R/A 23POS |
| SSW-120-02-S-D-RA | CONN RCPT .100" 40PS DL R/A GOLD |
| TISP7260F3P | SURGE SUPP 200V BIDIR 8-DIP |
| SMP14A-E3/85A | TVS 400W UNIDIR 14V 5% SMP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TISP7180F3SL-S | 功能描述:硅对称二端开关元件 Triple Element Bidirectional RoHS:否 制造商:Bourns 转折电流 VBO:40 V 最大转折电流 IBO:800 mA 不重复通态电流: 额定重复关闭状态电压 VDRM:25 V 关闭状态漏泄电流（在 VDRM IDRM 下）: 保持电流（Ih 最大值）:50 mA 开启状态电压:5 V 关闭状态电容 CO:120 pF 最大工作温度:+ 150 C 安装风格:SMD/SMT 封装 / 箱体:DO-214AA |
| TISP7180H3SL | 功能描述:硅对称二端开关元件 Triple Element Bidirectional RoHS:否 制造商:Bourns 转折电流 VBO:40 V 最大转折电流 IBO:800 mA 不重复通态电流: 额定重复关闭状态电压 VDRM:25 V 关闭状态漏泄电流（在 VDRM IDRM 下）: 保持电流（Ih 最大值）:50 mA 开启状态电压:5 V 关闭状态电容 CO:120 pF 最大工作温度:+ 150 C 安装风格:SMD/SMT 封装 / 箱体:DO-214AA |
| TISP7180H3SLS | 制造商:Bourns Inc 功能描述: |
| TISP7180H3SL-S | 功能描述:硅对称二端开关元件 Triple Element Bidirectional RoHS:否 制造商:Bourns 转折电流 VBO:40 V 最大转折电流 IBO:800 mA 不重复通态电流: 额定重复关闭状态电压 VDRM:25 V 关闭状态漏泄电流（在 VDRM IDRM 下）: 保持电流（Ih 最大值）:50 mA 开启状态电压:5 V 关闭状态电容 CO:120 pF 最大工作温度:+ 150 C 安装风格:SMD/SMT 封装 / 箱体:DO-214AA |
| TISP7180S | 制造商:Bourns Inc 功能描述: |
发布紧急采购，3分钟左右您将得到回复。