- 您现在的位置：买卖IC网 > PDF目录299979 > TK740SIL-2626 (TOKO INC) DUAL OUTPUT, FIXED POSITIVE LDO REGULATOR, PDSO8 PDF资料下载
参数资料
| 型号： | TK740SIL-2626 |
| 厂商： | TOKO INC |
| 元件分类： | 固定正电压多路输出LDO稳压器 |
| 英文描述： | DUAL OUTPUT, FIXED POSITIVE LDO REGULATOR, PDSO8 |
| 封装： | SOT-23, 8 PIN |
| 文件页数： | 13/29页 |
| 文件大小： | 584K |
| 代理商： | TK740SIL-2626 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
Page 20
January 22, 2002 TOKO, Inc.
TK740xxL
DEFINITION AND EXPLANATION OF TECHNICAL TERMS
OUTPUT VOLTAGE (V
OUT)
The output voltage is specified with V
IN = (VOUT(TYP) + 1 V)
and I
OUT = 5 mA.
MAXIMUM OUTPUT CURRENT (I
OUT(MAX))
The rated output current is specified under the condition
where the output voltage drops to V
OUT(TYP) x 0.9. The input
voltage is set to V
OUT(TYP) +1 V, and the current is pulsed to
minimize temperature effect. The output current decreases
during low voltage operation.
DROPOUT VOLTAGE (V
DROP)
The dropout voltage is the difference between the input
voltage and the output voltage at which point the regulator
starts to fall out of regulation (this is the point when the
output voltage decreases by 100 mV). Below this value, the
output voltage will fall as the input voltage is reduced. It is
dependent upon the load current and the junction tempera-
ture.
LINE REGULATION (Line Reg)
Line regulation is the ability of the regulator to maintain a
constant output voltage as the input voltage changes. The
line regulation is specified as the input voltage is changed
from V
IN = VOUT + 1 V to VIN = VOUT + 6 V. It is a pulsed
measurement to minimize temperature effects.
LOAD REGULATION (Load Reg)
Load regulation is the ability of the regulator to maintain a
constant output voltage as the load current changes. It is a
pulsed measurement to minimize temperature effects with
the input voltage set to V
IN = VOUT +1 V. The load regulation
is specified under two output current step conditions of 5 mA
to 100 mA and 5 mA to 200 mA.
QUIESCENT CURRENT (I
Q)
The quiescent current is the current which flows through the
ground terminal under no load conditions (I
OUT = 0 mA).
GROUND PIN CURRENT(I
GND)
The ground pin current is the current which flows through the
GND terminal according to load current. It is measured by
(input current-output current).
RIPPLE REJECTION RATIO (RR)
Ripple rejection is the ability of the regulator to attenuate the
ripple content of the input voltage at the output. It is
specified with 500 mV
RMS, 100 Hz and 1 MHz signal
superimposed on the input voltage, where V
IN = VOUT + 1.5
V. The output decoupling capacitor is set to 1.0 F, the C
FB
capacitor is set to 4700 pF, and the load current is set to 10
mA. Ripple rejection is the ratio of the ripple content of the
output vs. the input and is expressed in dB. Ripple rejection
can be improved by increasing the C
FB capacitor (However,
the on/off response time will increase).
STANDBY CURRENT (I
STBY)
Standby current is the current into the regulator when the
output is turned off by the control function. It is measured
with an input voltage of 8 V.
OVER CURRENT SENSOR
The overcurrent sensor protects the device when there is
excessive output current. it also protects the device if the
output is accidentally shorted to ground.
THERMAL SENSOR
The thermal sensor protects the device if the junction
temperature exceeds the safe value (T
j = 150 °C). This
temperature rise can be caused by extreme heat, excessive
power dissipation caused by large output voltage drops, or
excessive output current. The regulator will shut off when
the temperature exceeds the safe value. As the junction
temperature decreases, the regulator will begin to operate
again. Under sustained fault conditions, the regulator output
will oscillate as the device turns off then resets. Damage
may occur to the device under extreme fault conditions.
REVERSE VOLTAGE PROTECTION
Reverse voltage protection prevents damage due to the
output voltage being higher than the input voltage. This fault
condition can occur when the output capacitor remains
charged and the input is reduced to zero, or when an external
voltage higher than the input voltage is applied to the output
side. Toko’s regulators do not need an inherent diode
connected between the input and output. The maximum
reverse bias boltage is 6 V.
TK740xx
VOUT
VIN
GND
相关PDF资料 |
PDF描述 |
|---|---|
| TK740SIL-2727 | DUAL OUTPUT, FIXED POSITIVE LDO REGULATOR, PDSO8 |
| TL12W03-L(T30) | SINGLE COLOR LED, WARM WHITE |
| TL6700AF160QJ | KEYPAD SWITCH, SPST, MOMENTARY, 0.05A, 12VDC, 2.06 N, SURFACE MOUNT-STRAIGHT |
| TL750M05CKTE | 5 V FIXED POSITIVE LDO REGULATOR, 0.6 V DROPOUT, PSSO3 |
| TL750M05Y | 5 V FIXED POSITIVE LDO REGULATOR, 0.6 V DROPOUT, UUC3 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TK75 | 制造商:ALTECH 制造商全称:Altech corporation 功能描述:POLYCARBONATE ENCLOSURE TK 75 |
| TK7500 | 功能描述:冲压机与冲模 FRM W/4 DIES & CASE RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| TK75001 | 制造商:TOKO 制造商全称:TOKO, Inc 功能描述:PWM CONTROLLER |
| TK75001D | 制造商:TOKO 制造商全称:TOKO, Inc 功能描述:PWM CONTROLLER |
| TK75001DIMG | 制造商:TOKO 制造商全称:TOKO, Inc 功能描述:PWM CONTROLLER |
发布紧急采购，3分钟左右您将得到回复。