- 您现在的位置：买卖IC网 > PDF目录69486 > TL1454ACDG4 (TEXAS INSTRUMENTS INC) 1 A DUAL SWITCHING CONTROLLER, 2000 kHz SWITCHING FREQ-MAX, PDSO16 PDF资料下载
参数资料
| 型号： | TL1454ACDG4 |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 稳压器 |
| 英文描述： | 1 A DUAL SWITCHING CONTROLLER, 2000 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封装： | GREEN, SOIC-16 |
| 文件页数： | 20/25页 |
| 文件大小： | 503K |
| 代理商： | TL1454ACDG4 |
TL1454A, TL1454AY
DUALCHANNEL PULSEWIDTHMODULATION (PWM)
CONTROL CIRCUIT
SLVS423 A MAY 2002 REVISED SEPTEMBER 2002
4
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
theory of operation
reference voltage
A linear regulator operating from VCC generates a 2.5-V supply for the internal circuits and the 1.26-V reference,
which can source a maximum of 1 mA for external loads. A small ceramic capacitor (0.047
F to 0.1 F) between
REF and ground is recommended to minimize noise pickup.
error amplifier
The error amplifier generates the error signal used by the PWM to adjust the power-switch duty cycle for the
desired converter output voltage. The signal is generated by comparing a sample of the output voltage to the
voltage reference and amplifying the difference. An external resistive divider connected between the converter
output and ground, as shown in Figure 1, is generally required to obtain the output voltage sample.
The amplifier output is brought out on COMP to allow the frequency response of the amplifier to be shaped with
an external RC network to stabilize the feedback loop of the converter. DC loading on the COMP output is limited
to 45
A (the maximum amplifier source current capability).
Figure 1 illustrates the sense-divider network and error-amplifier connections for converters with positive output
voltages. The divider network is connected to the noninverting amplifier input because the PWM has a phase
inversion; the duty cycle decreases as the error-amplifier output increases.
_
+
IN
IN +
R3
R1
R2
COMP
To PWM
VO
Compensation
Network
REF
Converter
Output
TL1454A
Figure 1. Sense Divider/Error Amplifier
Configuration for Converters with Positive Outputs
The output voltage is given by:
V
O +
V
ref
1
) R1
R2
where Vref = 1.26 V.
The dc source resistance of the error-amplifier inputs should be 10 k
or less and approximately matched to
minimize output voltage errors caused by the input-bias current. A simple procedure for determining appropriate
values for the resistors is to choose a convenient value for R3 (10 k
or less) and calculate R1 and R2 using:
R
1 +
R
3
V
O
V
O
–V
ref
R
2 +
R
3
V
O
V
ref
相关PDF资料 |
PDF描述 |
|---|---|
| TL1454ACNSR | 1 A DUAL SWITCHING CONTROLLER, 2000 kHz SWITCHING FREQ-MAX, PDSO16 |
| TL1454ACNE4 | 1 A DUAL SWITCHING CONTROLLER, 2000 kHz SWITCHING FREQ-MAX, PDIP16 |
| TL1454ACN | 1 A DUAL SWITCHING CONTROLLER, 2000 kHz SWITCHING FREQ-MAX, PDIP16 |
| TL1454ACPWR | 1 A DUAL SWITCHING CONTROLLER, 2000 kHz SWITCHING FREQ-MAX, PDSO16 |
| TL1454ACDBR | 1 A DUAL SWITCHING CONTROLLER, 2000 kHz SWITCHING FREQ-MAX, PDSO16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TL1454ACDR | 功能描述:DC/DC 开关控制器 Dual-Ch PWM Control Circuit RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| TL1454ACDRG4 | 功能描述:DC/DC 开关控制器 Dual-Ch PWM Control Circuit RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| TL1454ACN | 功能描述:DC/DC 开关控制器 Dual ch PWM Ctlr RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| TL1454ACNE4 | 功能描述:DC/DC 开关控制器 Dual ch PWM Ctlr RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| TL1454ACNS | 制造商:TI 制造商全称:Texas Instruments 功能描述:DUAL-CHANNEL PULSE-WIDTH-MODULATION (PWM) CONTROL CIRCUIT |
发布紧急采购，3分钟左右您将得到回复。