参数资料
型号: TLC1514IDRG4
厂商: TEXAS INSTRUMENTS INC
元件分类: ADC
英文描述: 4-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO16
封装: GREEN, PLASTIC, SOIC-16
文件页数: 6/42页
文件大小: 645K
代理商: TLC1514IDRG4
TLC1514, TLC1518
5-V, 10-BIT, 400 KSPS, 4/8 CHANNEL, LOW POWER,
SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTO POWER DOWN
SLAS252 – DECEMBER 1999
14
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
conversion cycles (continued)
CS
CSTART
SDI
INT
EOC
SDO
Hi-Z
Select/Read
Cycle
Select/Read
Cycle
tsample
tconvert
Previous Conversion
Result
Previous Conversion
Result
FS
Hi-Z
This is one of the single shot commands. Conversion starts on next rising edge of CSTART.
Figure 9. Mode 00 Single Shot/Extended Sampling (FS signal used, FS pin connected to TMS320 DSP)
CS used as FS input
When interfacing with the TMS320 DSP using conversion mode 00, the FSR signal from the DSP may be
connected to the CS input if this is the only device on the serial port. This will save one output pin from the DSP.
Output data is made available on the rising edge of SCLK and input data is latched on the rising edge of SCLK
in this case.
modes using the FIFO: modes 01, 10, 11 timing
Modes 01, 10, and 11 timing are very similar except for how and when the FIFO is read, how the device is
configured, and how channel(s) are selected.
Mode 01 (repeat mode) requires a two-cycle configuration where the first one sets the mode and the second
one selects the channel. Once the FIFO is filled up to the threshold programmed, it has the option to either read
the FIFO or configure for other modes. Therefore, the sequence is either configure: select : triggered
conversions : FIFO read : select : triggered conversions : FIFO read or configure : select : triggered conversions
: configure : .... Each configure clears the FIFO and the action that follows the configure command depends on
the mode setting of the device.
NOTE:
When using CSTART to sample in extended mode, the falling edge of the first CSTART trigger
should occur no more than 1.5
s after the falling edge of CS (or falling edge of FS if FS is active)
of the channel select cycle (see Figure 11).
相关PDF资料
PDF描述
TLC1518IDW 8-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO20
TLC1518IPWR 8-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO20
TLC1518IPWG4 8-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO20
TLC1514ID 4-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO16
TLC1514IPW 4-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO16
相关代理商/技术参数
参数描述
TLC1514IPW 功能描述:模数转换器 - ADC 10bit 400kSPS SAR RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32
TLC1514IPWG4 功能描述:模数转换器 - ADC 10-Bit 400 kSPS Serial Out RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32
TLC1514IPWR 功能描述:模数转换器 - ADC 10-Bit 400 kSPS Serial Out RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32
TLC1514IPWRG4 功能描述:模数转换器 - ADC 10-Bit 400 kSPS Serial Out RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32
TLC1514PW 制造商:TI 制造商全称:Texas Instruments 功能描述:5-V, 10-BIT, 400 KSPS, 4/8 CHANNEL, LOW POWER, SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTO POWER DOWN