- 您现在的位置：买卖IC网 > PDF目录69493 > TLC32046IFNR (TEXAS INSTRUMENTS INC) SPECIALTY ANALOG CIRCUIT, PQCC28 PDF资料下载
参数资料
| 型号： | TLC32046IFNR |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PQCC28 |
| 封装： | PLASTIC, CC-28 |
| 文件页数： | 21/56页 |
| 文件大小： | 274K |
| 代理商： | TLC32046IFNR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页
2–14
FSR
FSX
t2
Secondary
Primary
Secondary
Primary
t1
Secondary
Primary
Transmit
Conversion
Preload A
Transmit
Conversion
Preload B
Transmit
Conversion
Preload C
Receive
Conversion
Period A
Receive
Conversion
Period B
Figure 2–7. More Than One Set of Primary and Secondary DX
Serial Communications Between Two Receive Frame Syncs
2.24 System Frequency Response Correction
The (sin x)/x correction for the DAC zero-order sample-and-hold output can be provided by an on-board
second-order (sin x)/x correction filter (see Functional Block Diagram). This (sin x)/x correction filter can be
inserted into or omitted from the signal path by digital-signal-processor control (data bit D9 in the DX
secondary communications). When inserted, the (sin x)/x correction filter precedes the switched-capacitor
low-pass filter. When the TB register (see Figure 2–1) equals 15, the correction results of Figures 5 – 5, 5 – 6,
and 5 –7 can be obtained.
The (sin x)/x correction [see section (sin x)/x] can also be accomplished by disabling the on-board
second-order correction filter and performing the (sin x)/x correction in digital signal processor software. The
system frequency response can be corrected via DSP software to
± 0.1 dB accuracy to a band edge of
3000 Hz for all sampling rates. This correction is accomplished with a first-order digital correction filter, that
requires seven TMS320 instruction cycles. With a 200-ns instruction cycle, seven instructions represent an
overhead factor of 1.1% and 1.3% for sampling rates of 8 and 9.6 kHz, respectively (see the (Sin x)/x
Correction Section for more details).
2.25 (Sin x)/x Correction
If the designer does not wish to use the on-board second-order (sin x)/x correction filter, correction can be
accomplished in digital signal processor (DSP) software. (Sin x)/x correction can be accomplished easily
and efficiently in digital signal processor software. Excellent correction accuracy can be achieved to a band
edge of 3000 Hz by using a first-order digital correction filter. The results shown are typical of the numerical
correction accuracy that can be achieved for sample rates of interest. The filter requires seven instruction
cycles per sample on the TMS320 DS. With a 200-ns instruction cycle, nine instructions per sample
represents an overhead factor of 1.4% and 1.7% for sampling rates of 8000 Hz and 9600 Hz, respectively.
This correction adds a slight amount of group delay at the upper edge of the 300-Hz to 3000-Hz band.
2.26 (Sin x)/x Roll-Off for a Zero-Order Hold Function
The (sin x)/x roll-off error for the AIC DAC zero-order hold function at a band-edge frequency of 3000 Hz
for the various sampling rates is shown in Table 2–5 (see Figure 5 –7).
相关PDF资料 |
PDF描述 |
|---|---|
| TLC32046MJ | SPECIALTY ANALOG CIRCUIT, CDIP28 |
| TLC320AD50CDW | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| TLC320AD52CDWR | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| TLC320AD50IDW | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| TLC320AD50CPTR | SPECIALTY ANALOG CIRCUIT, PQFP48 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TLC32046IN | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| TLC32046M | 制造商:TI 制造商全称:Texas Instruments 功能描述:Wide-Band Analog Interface Circuit |
| TLC32047 | 制造商:TI 制造商全称:Texas Instruments 功能描述:Wide-Band Analog Interface Circuit |
| TLC32047C | 制造商:TI 制造商全称:Texas Instruments 功能描述:Wide-Band Analog Interface Circuit |
| TLC32047CFN | 制造商:TI 制造商全称:Texas Instruments 功能描述:Wide-Band Analog Interface Circuit |
发布紧急采购，3分钟左右您将得到回复。