- 您现在的位置：买卖IC网 > PDF目录299979 > TLP2403(F) 1 CHANNEL LOGIC OUTPUT OPTOCOUPLER PDF资料下载
参数资料
| 型号： | TLP2403(F) |
| 元件分类： | 光电耦合器 |
| 英文描述： | 1 CHANNEL LOGIC OUTPUT OPTOCOUPLER |
| 封装： | ROHS COMPLIANT, 11-5K1S, SOP-8 |
| 文件页数： | 10/12页 |
| 文件大小： | 228K |
| 代理商： | TLP2403(F) |
TLP2403
7
13.
13. Soldering and Storage
Soldering and Storage
13.1.
13.1. Precautions for Soldering
Precautions for Soldering
The soldering temperature should be controlled as closely as possible to the conditions shown below, irrespective
of whether a soldering iron or a reflow soldering method is used.
When using soldering reflow (See Fig. 13.1.1 and 13.1.2)
Reflow soldering must be performed once or twice.
The mounting should be completed with the interval from the first to the last mountings being 2 weeks.
Fig.
Fig. 13.1.1
13.1.1
An example of a temperature profile
when Sn-Pb eutectic solder is used
Fig.
Fig. 13.1.2
13.1.2
An example of a temperature profile
when lead(Pb)-free solder is used
When using soldering flow (Applicable to both eutectic solder and Lead(Pb)-Free solder)
Apply preheating of 150 for 60 to 120 seconds.
Mounting condition of 260 within 10 seconds is recommended.
Flow soldering must be performed once.
When using soldering Iron (Applicable to both eutectic solder and Lead(Pb)-Free solder)
Complete soldering within 10 seconds for lead temperature not exceeding 260 or within 3 seconds not
exceeding 350
Heating by soldering iron must be done only once per lead.
13.2.
13.2. Precautions for General Storage
Precautions for General Storage
Avoid storage locations where devices may be exposed to moisture or direct sunlight.
Follow the precautions printed on the packing label of the device for transportation and storage.
Keep the storage location temperature and humidity within a range of 5 to 35 and 45% to 75%,
respectively.
Do not store the products in locations with poisonous gases (especially corrosive gases) or in dusty
conditions.
Store the products in locations with minimal temperature fluctuations. Rapid temperature changes during
storage can cause condensation, resulting in lead oxidation or corrosion, which will deteriorate the
solderability of the leads.
When restoring devices after removal from their packing, use anti-static containers.
Do not allow loads to be applied directly to devices while they are in storage.
If devices have been stored for more than two years under normal storage conditions, it is recommended
that you check the leads for ease of soldering prior to use.
2010-09-06
Rev.1.0
相关PDF资料 |
PDF描述 |
|---|---|
| TLP360J(IFT7)(D4) | 1 CHANNEL TRIAC OUTPUT OPTOCOUPLER |
| TLP521-2GBG | 2 CHANNEL TRANSISTOR OUTPUT OPTOCOUPLER |
| TLP590B(TP1) | SPECIALTY OPTOELECTRONIC DEVICE |
| TLP596G | TRANSISTOR OUTPUT SOLID STATE RELAY, 2500 V ISOLATION-MAX |
| TLSD-20-D-02.00-01-F | INTERCONNECTION DEVICE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TLP2404 | 制造商:TOSHIBA 制造商全称:Toshiba Semiconductor 功能描述:IPM (Intelligent Power Module) Industrial Inverter Operate at high ambient temperatures up to 125°C |
| TLP2404(F) | 功能描述:高速光耦合器 Photo-IC 6K Vpk 3750 1.6mA 30ns RoHS:否 制造商:Avago Technologies 电流传递比: 最大波特率: 最大正向二极管电压:1.75 V 最大反向二极管电压:5 V 最大功率耗散:40 mW 最大工作温度:+125 C 最小工作温度:- 40 C 封装 / 箱体:SOIC-5 封装:Tube |
| TLP2404(TP,F) | 制造商:Toshiba America Electronic Components 功能描述: |
| TLP2405 | 制造商:TOSHIBA 制造商全称:Toshiba Semiconductor 功能描述:Photocouplers GaA?As Infrared LED & Photo IC |
| TLP2405(F) | 功能描述:高速光耦合器 Photo-IC 6K Vpk 3750 1.6mA 30ns RoHS:否 制造商:Avago Technologies 电流传递比: 最大波特率: 最大正向二极管电压:1.75 V 最大反向二极管电压:5 V 最大功率耗散:40 mW 最大工作温度:+125 C 最小工作温度:- 40 C 封装 / 箱体:SOIC-5 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。