参数资料
型号: TLV2472IDGNRG4
厂商: TEXAS INSTRUMENTS INC
元件分类: 运算放大器
英文描述: DUAL OP-AMP, 2400 uV OFFSET-MAX, 2.8 MHz BAND WIDTH, PDSO8
封装: GREEN, PLASTIC, MSOP-8
文件页数: 8/59页
文件大小: 2567K
代理商: TLV2472IDGNRG4
www.ti.com
GENERAL CONFIGURATIONS
VI
VO
C1
+
RG
RF
R1
f
–3dB +
1
2pR1C1
V
O
V
I
+
1 )
R
F
R
G
1
1 ) sR1C1
VI
C2
R2
R1
C1
RF
RG
R1 = R2 = R
C1 = C2 = C
Q = Peaking Factor
(Butterworth Q = 0.707)
(
=
1
Q
2 –
)
RG
RF
_
+
f
–3dB +
1
2pRC
SHUTDOWN FUNCTION
SLOS232E – JUNE 1999 – REVISED JULY 2007
APPLICATION INFORMATION (continued)
When receiving low-level signals, limiting the bandwidth of the incoming signals into the system is often
required. The simplest way to accomplish this is to place an RC filter at the noninverting terminal of the amplifier
(see Figure 44).
Figure 44. Single-Pole Low-Pass Filter
If even more attenuation is needed, a multiple pole filter is required. The Sallen-Key filter can be used for this
task. For best results, the amplifier should have a bandwidth that is eight to ten times the filter frequency
bandwidth. Failure to do this can result in phase shift of the amplifier.
Figure 45. 2-Pole Low-Pass Sallen-Key Filter
Three members of the TLV247x family (TLV2470/3/5) have a shutdown terminal for conserving battery life in
portable applications. When the shutdown terminal is tied low, the supply current is reduced to 350nA/channel,
the amplifier is disabled, and the outputs are placed in a high impedance mode. To enable the amplifier, the
shutdown terminal can either be left floating or pulled high. When the shutdown terminal is left floating, care
should be taken to ensure that parasitic leakage current at the shutdown terminal does not inadvertently place
the operational amplifier into shutdown. The shutdown terminal threshold is always referenced to VDD/2.
Therefore, when operating the device with split supply voltages (e.g.,
±2.5V), the shutdown terminal needs to be
pulled to VDD– (not GND) to disable the operational amplifier.
The amplifier output with a shutdown pulse is shown in Figure 33 and Figure 34. The amplifier is powered with a
single 5V supply and configured as a noninverting configuration with a gain of 5. The amplifier turn-on and
turn-off times are measured from the 50% point of the shutdown pulse to the 50% point of the output waveform.
The times for the single, dual, and quad versions are listed in the data tables.
16
相关PDF资料
PDF描述
TLV2472IPE4 DUAL OP-AMP, 2400 uV OFFSET-MAX, 2.8 MHz BAND WIDTH, PDIP8
TLV2472AIDG4 DUAL OP-AMP, 1800 uV OFFSET-MAX, 2.8 MHz BAND WIDTH, PDSO8
TLV2472CDG4 DUAL OP-AMP, 2400 uV OFFSET-MAX, 2.8 MHz BAND WIDTH, PDSO8
TLV2620IDBVRG4 OP-AMP, 4500 uV OFFSET-MAX, 11 MHz BAND WIDTH, PDSO6
TLV2624IPWRG4 QUAD OP-AMP, 4500 uV OFFSET-MAX, 11 MHz BAND WIDTH, PDSO14
相关代理商/技术参数
参数描述
TLV2472IDR 功能描述:运算放大器 - 运放 Dual Lo-Pwr R-to-R Input/Output Op Amp RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比(最小值):63 dB 输入补偿电压:1 mV 输入偏流(最大值):10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel
TLV2472IDRG4 功能描述:运算放大器 - 运放 Dual Lo-Pwr R-to-R Input/Output Op Amp RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比(最小值):63 dB 输入补偿电压:1 mV 输入偏流(最大值):10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel
TLV2472IP 功能描述:运算放大器 - 运放 Dual Rail-Rail RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比(最小值):63 dB 输入补偿电压:1 mV 输入偏流(最大值):10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel
TLV2472IP 制造商:Texas Instruments 功能描述:IC DUAL OP-AMP ((NW)) 制造商:Texas Instruments 功能描述:IC, OP-AMP, 2.8MHz, 1.4V/ us, DIP-8
TLV2472IPE4 功能描述:运算放大器 - 运放 Dual Lo-Pwr R-to-R Input/Output Op Amp RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比(最小值):63 dB 输入补偿电压:1 mV 输入偏流(最大值):10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel