- 您现在的位置：买卖IC网 > PDF目录98252 > TLV2553IDWG4 (TEXAS INSTRUMENTS INC) 11-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO20 PDF资料下载
参数资料
| 型号： | TLV2553IDWG4 |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | ADC |
| 英文描述： | 11-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO20 |
| 封装： | GREEN, PLASTIC, SOIC-20 |
| 文件页数： | 13/29页 |
| 文件大小： | 603K |
| 代理商： | TLV2553IDWG4 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
TLV2553
SLAS354B – SEPTEMBER 2001 – REVISED SEPTEMBER 2002
20
www.ti.com
PRINCIPLES OF OPERATION
detailed description
Initially, with chip select (CS) high, I/O CLOCK and DATA IN are disabled and DATA OUT is in the
high-impedance state. CS going low begins the conversion sequence by enabling I/O CLOCK and DATA IN and
removes DATA OUT from the high-impedance state. The input data is an 8–bit data stream consisting of a 4-bit
address or command (D7–D4) and a 4-bit configuration data (D3–D0). Configuration register 1, CFGR1, which
controls output data format configuration, consists of a 2-bit data length select (D3–D2), an output MSB or LSB
first bit (D1), and a unipolar or bipolar output select bit (D0) that are applied to any command (from DATA IN)
except for command 1111b. The I/O CLOCK sequence applied to the I/O CLOCK terminal transfers this data
to the input data register. During this transfer, the I/O CLOCK sequence also shifts the previous conversion
result from the output data register to DATA OUT. I/O CLOCK receives the input sequence of 8, 12, or 16 clock
cycles long depending on the data-length selection in the input data register. Sampling of the analog input
begins on the fourth falling edge of the input I/O CLOCK sequence and is held after the last falling edge of the
I/O CLOCK sequence. The last falling edge of the I/O CLOCK sequence also takes EOC low and begins the
conversion.
converter operation
The operation of the converter is organized as a succession of three distinct cycles: 1) the data I/O cycle, 2)
the sampling cycle and 3) the conversion cycle. The first two are partially overlapped.
data I/O cycle
The data I/O cycle is defined by the externally provided I/O CLOCK and lasts 8, 12, or 16 clock periods,
depending on the selected output data length. During the I/O cycle, the following two operations take place
simultaneously. An 8-bit data stream consisting of address/command and configuration information is provided
to DATA IN. This data is shifted into the device on the rising edge of the first eight I/O CLOCK clocks. DATA
INPUT is ignored after the first eight clocks during 12- or 16-clock I/O transfers. The data output, with a length
of 8, 12, or 16 bits, is provided serially on DATA OUT. When CS is held low, the first output data bit occurs on
the rising edge of EOC. When CS is toggled between conversions, the first output data bit occurs on the falling
edge of CS. This data is the result of the previous conversion period, and after the first output data bit, each
succeeding bit is clocked out on the falling edge of each succeeding I/O CLOCK.
sampling cycle
During the sampling cycle, one of the analog inputs is internally connected to the capacitor array of the converter
to store the analog input signal. The converter starts sampling the selected input immediately after the four
address/command bits have been clocked into the input data register. Sampling starts on the fourth falling edge
of I/O CLOCK. The converter remains in the sampling mode until the eighth, twelfth, or sixteenth falling edge
of the I/O CLOCK depending on the data-length selection.
After the 8-bit data stream has been clocked in, DATA IN should be held at a fixed digital level until EOC goes
high (indicating that the conversion is complete) to maximize the sampling accuracy and minimize the influence
of external digital noise.
相关PDF资料 |
PDF描述 |
|---|---|
| TLV2553IPWR | 11-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO20 |
| TLV2553IDWRG4 | 11-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO20 |
| TLV2553IPWRG4 | 11-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO20 |
| TLV2553IDW | 11-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO20 |
| TLV2553IPWG4 | 11-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO20 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TLV2553IDWR | 功能描述:模数转换器 - ADC 12bit 200kSPS ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| TLV2553IDWRG4 | 功能描述:模数转换器 - ADC 12-Bit 200 KSPS 11 Ch Lo-Pwr RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| TLV2553IDWRQ1 | 功能描述:模数转换器 - ADC Auto Cat 12B 200KSPS 11Ch Low-Pwr Ser ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| TLV2553IPW | 功能描述:模数转换器 - ADC 12-Bit 200 KSPS 11 Ch Lo-Pwr RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| TLV2553IPWG4 | 功能描述:模数转换器 - ADC 12-Bit 200 KSPS 11 Ch Lo-Pwr RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。