- 您现在的位置：买卖IC网 > PDF目录98252 > TLV320AIC10CGQER (TEXAS INSTRUMENTS INC) SPECIALTY CONSUMER CIRCUIT, PBGA80 PDF资料下载
参数资料
| 型号： | TLV320AIC10CGQER |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 消费家电 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PBGA80 |
| 封装： | MICRO, PLASTIC, BGA-80 |
| 文件页数： | 11/57页 |
| 文件大小： | 454K |
| 代理商： | TLV320AIC10CGQER |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页
2–5
2.1.10 Analog and Digital Loopback
The analog and digital loopbacks provide a means of testing the modem data ADC/DAC channels and can be used
for in-circuit system level tests. The analog loopback routes the DAC low-pass filter output into the analog input where
it is then converted by the ADC to a digital word. The digital loopback routes the ADC output to the DAC input on the
device. Analog loopback is enabled by writing 01 to bits D7 and D6 respectively in control register 3. Digital loopback
is enabled by writing 10 to bits D7 and D6 in control register 3 (see Appendix A).
2.1.11 FIR Overflow Flag
The decimator FIR filter sets an overflow flag (bit D7) in control register 1 to indicate that the input analog signal has
exceeded the range of the internal decimation-filter calculations. When the FIR overflow flag has been set in the
register, it remains set until the register is read by the user. Reading this value resets the overflow flag.
If FIR overflow occurs, the input signal has to be attenuated either by the PGA or some other method.
2.1.12 FIR Bypass Mode
An option is provided to bypass the FIR filter sections of the decimation and interpolation filters. This mode is selected
through bit D2 of control register 1, and effectively increases the frequency of the FS and SCLK signals to 4 times
the normal FIR-filter output rate, since the decimation/interpolation factor of the bypassed filter stage is 4. The sinc
filters of the two paths can not be bypassed.
The AIC10 is capable of supporting a maximum of four devices in cascade.
If the FIR filter is bypassed, the signal-to-noise ratio (SNR) is reduced to 69 dB. The FIR bypass mode offers users
the flexibility to implement their own decimation/interpolation FIR filter based on application-specific requirements.
For example users can select this mode to bypass both decimation and interpolation FIR filters and implement a
lower-order FIR filter or an IIR filter externally in the DSP for applications that require group delays smaller than 17/Fs,
which is the AIC10s total group delay.
2.1.13 Low-Power Mode
To select the low-power mode, in which the AIC10 typically consumes 38.6 mW, set bit D7 of control register 2 to 1
and set the sampling rate at 8 ksps.
2.1.14 Event-Monitor Mode
This mode is only available during the register-write cycle, and is enabled by writing 11 to bits D6 and D7 of control
register 3; performing a register read terminates event-monitor mode3. The event monitor mode is provided for
applications that need hardware control and monitoring of external events. By allowing the device to drive the FLAG
terminal (set through bit D3 of the control register 3), the host DSP is capable of system control through the same
serial port that connects the device. Along with this control is the capability of monitoring the value of the ALTIN
terminal during a secondary communication cycle. One application of this function is in monitoring RING DETECT
or OFFHOOK DETECT from a phone-answering system. FLAG allows response to these incoming control signals.
Figure 2–6 shows the timing associated with this operating mode.
FS
DOUT
ALTDI
Primary
Secondary
16 bits
NOTE A: When DIN performs a write operation (sets D12 to 0) during secondary communication.
Figure 2–6. Event Monitor Mode Timing
相关PDF资料 |
PDF描述 |
|---|---|
| TLV320AIC10IGQER | SPECIALTY CONSUMER CIRCUIT, PBGA80 |
| TLV320AIC11C | SPECIALTY CONSUMER CIRCUIT, PQFP48 |
| TLV320AIC11I | SPECIALTY CONSUMER CIRCUIT, PQFP48 |
| TLV320AIC11CPFB | SPECIALTY CONSUMER CIRCUIT, PQFP48 |
| TLV320AIC11IPFB | SPECIALTY CONSUMER CIRCUIT, PQFP48 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TLV320AIC10CPFB | 功能描述:接口—CODEC 16-Bit 22-KSPS DSP Codec RoHS:否 制造商:Texas Instruments 类型: 分辨率: 转换速率:48 kSPs 接口类型:I2C ADC 数量:2 DAC 数量:4 工作电源电压:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-81 封装:Reel |
| TLV320AIC10CPFBG4 | 功能描述:接口—CODEC 16-Bit Reg Trnscvr With 3-State Outputs RoHS:否 制造商:Texas Instruments 类型: 分辨率: 转换速率:48 kSPs 接口类型:I2C ADC 数量:2 DAC 数量:4 工作电源电压:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-81 封装:Reel |
| TLV320AIC10EVM | 功能描述:音频 IC 开发工具 TLV320AIC10 Eval Mod RoHS:否 制造商:Texas Instruments 产品:Evaluation Kits 类型:Audio Amplifiers 工具用于评估:TAS5614L 工作电源电压:12 V to 38 V |
| TLV320AIC10I | 制造商:TI 制造商全称:Texas Instruments 功能描述:General-Purpose 3V to 5.5V 16-bit 22-KSPS DSP CODEC |
| TLV320AIC10IGQER | 功能描述:接口—CODEC 16-Bit 22-KSPS DSP Codec RoHS:否 制造商:Texas Instruments 类型: 分辨率: 转换速率:48 kSPs 接口类型:I2C ADC 数量:2 DAC 数量:4 工作电源电压:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-81 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。