- 您现在的位置：买卖IC网 > PDF目录98253 > TLV320AIC26IRHB (TEXAS INSTRUMENTS INC) SPECIALTY CONSUMER CIRCUIT, PQCC32 PDF资料下载
参数资料
| 型号： | TLV320AIC26IRHB |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 消费家电 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PQCC32 |
| 封装： | 5 X 5 MM, GREEN, PLASTIC, QFN-32 |
| 文件页数： | 17/67页 |
| 文件大小： | 883K |
| 代理商： | TLV320AIC26IRHB |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页
TLV320AIC26
SLAS412 DECEMBER 2003
www.ti.com
24
The ’AIC26 also includes functionality to detect when the user switches are on or off the de-emphasis or digital audio
processing functions, to first (1) soft-mute the DAC volume control, (2) change the operation of the digital effects
processing, and (3) soft-unmute the part. This avoids any possible pop/clicks in the audio output due to instantaneous
changes in the filtering. A similar algorithm is used when first powering up or down the DAC. The circuit begins operation
at power up with the volume control muted, then soft-steps it up to the desired volume level. At power down, the logic first
soft-steps the volume down to a mute level, then powers down the circuitry.
DAC Power Down
The DAC power-down flag ( D6 of REG05H/Page2) along with D10 of REG05H/Page2 denotes the power-down status
of the DAC according to Table 3.
Table 3. DAC Powerdown Status
[D10,D6]
POWERUP / DOWN STATE OF DAC
[0,0]
DAC is in stable power-up state
[0,1]
DAC is in the process of powering up. The length of this state is determined by PLL and output driver
power-up delays controlled by register programming.
[1,0]
DAC is in the process of powering down. The length of this state is determined by soft-stepping of volume
control block and DAC pop reduction sequencing controlled by register programming.
[1,1]
DAC is in a stable power-down state.
AUDIO OUTPUT DRIVERS
The ’AIC26 features audio output drivers which can be configured in either low power mode or high power mode depending
on the load and output power required. By default, at reset the output drivers are configured in low power mode. In this mode,
the output drivers can drive a full-scale line-level signal into loads of 10 k
minimum or drive moderate amplitude signals
into loads of 16
minimum.
The output drivers can also be configured in high power mode by setting bit D12 of Reg05H/Page2 to 1. In this mode, each
output driver can deliver up to 30 mW per channel into a headphone speaker load of 16
. The headphones can be
connected in a single-ended configuration using ac-coupling capacitors, or the capacitors can be removed and virtual
ground (VGND) powered for a capless output connection. The typical headphone jack configuration for these two modes
is shown in Figure 21. Note that the VGND amplifier must be powered if the capless configuration is used.
In the case of an ac-coupled output, the value of the capacitors is typically chosen based on the amount of low-frequency
cut that can be tolerated. The capacitor in series with the load impedance forms a high-pass filter with 3 dB cutoff frequency
of 1/(2
πRC) in Hz, where R is the impedance of the headphones. Use of an overly small capacitor reduces low-frequency
components in the signal output and leads to low-quality audio. When driving 16-
headphones, capacitors of 220-F (a
commonly used value) result in a high-pass filter cutoff frequency of 45 Hz, although reducing these capacitors to 50
F
results in a cutoff frequency of 199 Hz, which is generally considered noticeable when playing music. The cutoff frequency
is reduced to half of the above values if 32-
headphones are used instead of 16 .
The ’AIC26 programmable digital effects block can be used to help reduce the size of capacitors needed by implementing
a low frequency boost function to help compensate for the high-pass filter introduced by the ac-coupling capacitors. For
example, by using 50-
F capacitors and setting the ’AIC26 programmable filter coefficients as shown below, the frequency
response can be improved as shown in Figure 20.
Filter coefficients (use the same for both channels):
N0 = 32767, N1 = 32346, N2 = 31925, N3 = 32767, N4 = 0, N5 = 0
D0 = 32738, D1 = 32708 D4 = 0, D5 = 0
相关PDF资料 |
PDF描述 |
|---|---|
| TLV320AIC26IRHBG4 | SPECIALTY CONSUMER CIRCUIT, PQCC32 |
| TLV320AIC26IRHBRG4 | SPECIALTY CONSUMER CIRCUIT, PQCC32 |
| TLV320AIC27CPFB | SPECIALTY CONSUMER CIRCUIT, PQFP48 |
| TLV320AIC27IPFB | SPECIALTY CONSUMER CIRCUIT, PQFP48 |
| TLV320AIC27TPFB | SPECIALTY CONSUMER CIRCUIT, PQFP48 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TLV320AIC26IRHBG4 | 功能描述:接口—CODEC Octal Bus Trnscvr With 3-State Outputs RoHS:否 制造商:Texas Instruments 类型: 分辨率: 转换速率:48 kSPs 接口类型:I2C ADC 数量:2 DAC 数量:4 工作电源电压:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-81 封装:Reel |
| TLV320AIC26IRHBR | 功能描述:接口—CODEC Lo-Pwr Stereo Codec RoHS:否 制造商:Texas Instruments 类型: 分辨率: 转换速率:48 kSPs 接口类型:I2C ADC 数量:2 DAC 数量:4 工作电源电压:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-81 封装:Reel |
| TLV320AIC26IRHBRG4 | 功能描述:接口—CODEC Lo-Pwr Stereo Codec RoHS:否 制造商:Texas Instruments 类型: 分辨率: 转换速率:48 kSPs 接口类型:I2C ADC 数量:2 DAC 数量:4 工作电源电压:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-81 封装:Reel |
| TLV320AIC27 | 制造商:TI 制造商全称:Texas Instruments 功能描述:STEREO AUDIO CODEC |
| TLV320AIC27CPFB | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Texas Instruments 功能描述: |
发布紧急采购，3分钟左右您将得到回复。