- 您现在的位置：买卖IC网 > PDF目录199414 > TND332ST (SANYO SEMICONDUCTOR CO LTD) 1 A HALF BRIDGE BASED PRPHL DRVR, PDSO8 PDF资料下载
参数资料
| 型号： | TND332ST |
| 厂商： | SANYO SEMICONDUCTOR CO LTD |
| 元件分类： | 外设及接口 |
| 英文描述： | 1 A HALF BRIDGE BASED PRPHL DRVR, PDSO8 |
| 封装： | SOP-8 |
| 文件页数： | 4/5页 |
| 文件大小： | 264K |
| 代理商： | TND332ST |
www.nikkaiswitches.com Nihon Kaiheiki Phone 81-44-813-8008 Fax 81-44-813-8038
5-08
Half-Inch Diameter Process Sealed Rotaries
Series MR
Pole
Model
Number of Positions
Stopper Settings
Number of Terminals
Schematics
SP
MRA112
MRF112
MRK112
2–12
2, 3, 4, . . . 12
1 COM, 12 LOAD
DP
MRA206
MRF206
MRK206
2–6
2, 3, 4, 5, 6
2 COM, 12 LOAD
4P
MRA403
MRF403
MRK403
2–3
2, 3
4 COM, 12 LOAD
POLES & CIRCUITS
12 34 56 78 9101112
A
12 34 56 12 34 56
A
B
12 31 23 12 31 23
A
B
C
D
POSITION SETTING FOR MRA, MRF, & MRK MODELS
Each switch is supplied with the stopper set for the maximum number of positions allowed for that model. Prior to installation,
the desired position setting should be made. Contact factory for continuous rotation.
MRF Models
1. Remove the protective cover from the switch body.
2. Turn the shaft counterclockwise to the extreme left by using a screwdriver.
3. Inside the cover is a magnifying lens which would be positioned over the
number which is to be the maximum position used; when the cover is then
snapped into the switch, the projection beside the lens fits into the correct
hole for setting the stop.
2
1 C 12 11 10
M R
-
12
3 4
5 6 7 8
9
1011
12
Protective Cover
Lens
Projection
MRK & MRA Models
1. Using the actuator knob, turn the shaft
counterclockwise to the extreme left. If
the shaft is not turned counterclockwise
to the extreme left, proper setting can-
not be achieved. At this extreme posi-
tion, the white line on the knob points
to the number 1 position shown on the
side of the switch.
2. Remove the knob from the shaft and
loosen the nut far enough to allow rais-
ing the stopper plate, plus washer(s),
for resetting to the desired position.
3. Note the position numbers on the side
of the switch; these correspond to the
terminal numbers and stopper holes.
Insert the stopper in the hole numbered
for the maximum desired number of
stop settings. Satisfactory switch func-
tioning cannot be assured if the stopper
plate is not properly positioned.
4. Tighten the nut (beveled side up) firmly
against the stopper plate.
12
11
10
9
1
12
11
10
2
M R - K 1 1 2
2
1 C
12
11
10
9
12 11 10
9
Standard Mounting Hardware
Packaged Loose with Each Switch:
Hex Face Nut
Locking Ring
Lockwasher
Rubber Ring (MRK)
Factory Assembled:
Hex Nut
Stopper Plate
Metal Washer (MRA)
Rubber Washer
相关PDF资料 |
PDF描述 |
|---|---|
| TNF10-250MD | WIRE TERMINAL |
| TNGBJ1-1-S-D10 | PANEL MOUNT, FEMALE, BNC, TRIAXIAL CONNECTOR, JACK |
| TNGBJ1-10-S-D10 | PANEL MOUNT, FEMALE, BNC, TRIAXIAL CONNECTOR, JACK |
| TNGBJFL1-6-S-D8 | PANEL MOUNT, FEMALE, BNC, TRIAXIAL CONNECTOR, JACK |
| TNGBJTL1-1-S-D5 | PANEL MOUNT, FEMALE, BNC, TRIAXIAL CONNECTOR, JACK |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TND505MD | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:SWITCHING AMP DRIVE |
| TND505MD-TL-E | 功能描述:IC DVR HALF-BRIDGE 600V MFP16 RoHS:是 类别:集成电路 (IC) >> PMIC - MOSFET，电桥驱动器 - 内部开关 系列:- 标准包装:1,000 系列:- 类型:高端/低端驱动器 输入类型:SPI 输出数:8 导通状态电阻:850 毫欧，1.6 欧姆 电流 - 输出 / 通道:205mA，410mA 电流 - 峰值输出:500mA，1A 电源电压:9 V ~ 16 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 供应商设备封装:PG-DSO-20-45 包装:带卷 (TR) |
| TND506MD | 制造商:未知厂家 制造商全称:未知厂家 功能描述: |
| TND506MDTLE | 制造商:SANYO 功能描述:16MFP phCo Tape & Reel 制造商:Sanyo 功能描述:Excellent Power Device 16-Pin MFP T/R |
| TND506MD-TL-E | 功能描述:IC DVR HALF-BRIDGE 600V MFP16 RoHS:是 类别:集成电路 (IC) >> PMIC - MOSFET，电桥驱动器 - 内部开关 系列:- 标准包装:1,000 系列:- 类型:高端/低端驱动器 输入类型:SPI 输出数:8 导通状态电阻:850 毫欧，1.6 欧姆 电流 - 输出 / 通道:205mA，410mA 电流 - 峰值输出:500mA，1A 电源电压:9 V ~ 16 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 供应商设备封装:PG-DSO-20-45 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。