- 您现在的位置：买卖IC网 > Datasheet目录366 > TO263-5EV-VREG (Microchip Technology)EVAL BOARD VREG TO220-5/TO263-5 Datasheet资料下载
参数资料
| 型号： | TO263-5EV-VREG |
| 厂商： | Microchip Technology |
| 文件页数： | 12/20页 |
| 文件大小： | 0K |
| 描述： | EVAL BOARD VREG TO220-5/TO263-5 |
| 标准包装： | 1 |
| 每 IC 通道数： | 1 - 单 |
| 稳压器类型： | 正固定式和可调式 |
| 板类型： | 部分填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | TO-220-5 和 TO-263-5（D²Pak-5）封装 |
| 产品目录页面： | 659 (CN2011-ZH PDF) |
TO220-5 / TO263-5 Voltage Regulator Evaluation Board User’s Guide
9. Vary the input voltage to obtain data for ground current versus input voltage. With
no load attached to the output of the voltage regulator, the measured ground
current is also called the quiescent current of the regulator.
10. Add a load selection jumper, JP4 or JP5.
11. Read the Ground Current directly from the ampere meter connected to testpoints
TP6 and TP7.
12. The data collected will be the ground curren t versus load current.
2.3.2
Load Resistance
R5 and R6 are used to set desired load values. One choice is to set R5 to the minimum
current desired for testing. R6 would then be set to a value desired for specific tests.
Either value may be selected by adding their respective jumpers.
2.3.3
Line Step
Dynamic Line Step response may be evaluated by connecting an electronically
switched input voltage to testpoints TP1(+) and TP2(-) or to connector J1. An
oscilloscope is connected to TP3(Ch1 Trigger), TP9(Ch2) and TP10(Gnd). An
appropriate load is selected using R5 and JP4 or R6 and JP5. The input voltage is then
electronically switched from a low voltage to a high voltage. The corresponding voltage
waveform data of the voltage regulator response is captured by the oscilloscope.
Microchip will be offering a Line Step module that connects directly to connector J1.
The Line Step module will be capable of switching between two voltage levels that the
user supplies.
2.3.4
Load Step
Dynamic Load Step response may be evaluated by connecting an electronically
switched load to testpoints TP9(+) and TP10(-) or to connector P1. An oscilloscope is
connected to the electronic load switch signal (Ch1 Trigger) and to TP9(Ch2) and
TP10(Gnd). The load is then electronically switched from a high resistance to a low
resistance. The corresponding voltage waveform data of the voltage regulator
response is captured by the oscilloscope. Microchip will be offering a Load Step module
that connects directly to connector P1. The Load Step module will have several
selectable load values populated onboard to cover a wide range of loads. The load will
have the ability to be electronically or manually switched.
2.3.5
Power Supply Rejection Ratio (PSRR)
Power Supply Rejection Ratio tests are performed by removing the input capacitor
jumper, JP1, and connecting an appropriate PSRR analyzer to the TO220-5 / TO263-5
Voltage Regulator Evaluation Board. The PSRR analyzer may then sweep the input
voltage frequencies and record the corresponding output voltages.
DS51817A-page 8
? 2009 Microchip Technology Inc.
相关PDF资料 |
PDF描述 |
|---|---|
| TOOLSTICK-EK | KIT TOOL EVAL SYS IN A USB STICK |
| TPS23757EVM | EVALUATION MODULE FOR TPS23757 |
| TPS62230EVM-370 | EVAL MODULE FOR TPS62230-370 |
| TRAVELCUBE | SURGE SUP 1OUT W/RJ11 DIRECTPLUG |
| TRAVELER100BT | SURGE SUP 2OUT W/RJ11 DIRECTPLUG |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TO-263AB | 制造商:VISHAY 制造商全称:Vishay Siliconix 功能描述:High-Voltage Trench MOS Barrier Schottky Rectifier |
| TO263SHT | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| TO-264 | 制造商:IXYS 制造商全称:IXYS Corporation 功能描述:LinearL2 Power MOSFET w/Extended FBSOA |
| TO-268 | 制造商:IXYS 制造商全称:IXYS Corporation 功能描述:PolarHV Power MOSFET |
| TO-269AA | 制造商:FORMOSA 制造商全称:Formosa MS 功能描述:Case No. TO-269AA Device |
发布紧急采购，3分钟左右您将得到回复。