- 您现在的位置：买卖IC网 > PDF目录19732 > TOP243GN (Power Integrations)IC OFFLINE SWIT OVP UVLO HV 8SMD PDF资料下载
参数资料
| 型号： | TOP243GN |
| 厂商： | Power Integrations |
| 文件页数： | 6/52页 |
| 文件大小： | 0K |
| 描述： | IC OFFLINE SWIT OVP UVLO HV 8SMD |
| 标准包装： | 50 |
| 系列： | TOPSwitch®-GX |
| 输出隔离： | 隔离 |
| 频率范围： | 66 ~ 132kHz |
| 输出电压： | 700V |
| 功率（瓦特）： | 25W |
| 工作温度： | -40°C ~ 150°C |
| 封装/外壳： | 8-SMD（7 个接脚），鸥形翼 |
| 供应商设备封装： | SMD-8B |
| 包装： | 管件 |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
TOP242-250
CONTROL (C) Pin Operation
The CONTROL pin is a low impedance node that is capable
of receiving a combined supply and feedback current. During
normal operation, a shunt regulator is used to separate the
feedback signal from the supply current. CONTROL pin voltage
V C is the supply voltage for the control circuitry including the
MOSFET gate driver. An external bypass capacitor closely
connected between the CONTROL and SOURCE pins is required
to supply the instantaneous gate drive current. The total amount
of capacitance connected to this pin also sets the auto-restart
timing as well as control loop compensation.
When recti?ed DC high voltage is applied to the DRAIN
pin during start-up, the MOSFET is initially off, and the
CONTROL pin capacitor is charged through a switched high
voltage current source connected internally between the DRAIN
and CONTROL pins. When the CONTROL pin voltage V C
reaches approximately 5.8 V, the control circuitry is activated
and the soft-start begins. The soft-start circuit gradually
increases the duty cycle of the MOSFET from zero to the
maximum value over approximately 10 ms. If no external
feedback/supply current is fed into the CONTROL pin by the
end of the soft-start, the high voltage current source is turned
off and the CONTROL pin will start discharging in response
to the supply current drawn by the control circuitry. If the
power supply is designed properly, and no fault condition
such as open loop or shorted output exists, the feedback loop
will close, providing external CONTROL pin current, before
the CONTROL pin voltage has had a chance to discharge to
the lower threshold voltage of approximately 4.8 V (internal
supply under-voltage lockout threshold). When the externally
fed current charges the CONTROL pin to the shunt regulator
V UV
V LINE
0 V
voltage of 5.8 V, current in excess of the consumption of the
chip is shunted to SOURCE through resistor R E as shown in
Figure 2. This current ?owing through R E controls the duty cycle
of the power MOSFET to provide closed loop regulation. The
shunt regulator has a ?nite low output impedance Z C that sets
the gain of the error ampli?er when used in a primary feedback
con?guration. The dynamic impedance Z C of the CONTROL
pin together with the external CONTROL pin capacitance sets
the dominant pole for the control loop.
When a fault condition such as an open loop or shorted output
prevents the ?ow of an external current into the CONTROL
pin, the capacitor on the CONTROL pin discharges towards
4.8 V. At 4.8 V, auto-restart is activated which turns the output
MOSFET off and puts the control circuitry in a low current
standby mode. The high-voltage current source turns on and
charges the external capacitance again. A hysteretic internal
supply under-voltage comparator keeps V C within a window
of typically 4.8 V to 5.8 V by turning the high-voltage current
source on and off as shown in Figure 8. The auto-restart
circuit has a divide-by-eight counter which prevents the output
MOSFET from turning on again until eight discharge/charge
cycles have elapsed. This is accomplished by enabling the
output MOSFET only when the divide-by-eight counter reaches
full count (S7). The counter effectively limits TOPSwitch-GX
power dissipation by reducing the auto-restart duty cycle
to typically 4%. Auto-restart mode continues until output
voltage regulation is again achieved through closure of the
feedback loop.
Oscillator and Switching Frequency
The internal oscillator linearly charges and discharges an
V C
S7
S0
S1
S2
S6
S7
S0
S1
S2
S6
S7
S0
S1
S2
S6
S7
S7
5.8 V
4.8 V
0 V
V DRAIN
0 V
V OUT
0 V
1
2
3
2
4
NOTE: S0 THROUGH S7 ARE THE OUTPUT STATES OF THE AUTO-RESTART COUNTER
Figure 8. Typical Waveforms for (1) Power Up (2) Normal Operation (3) Auto-Restart (4) Power Down.
PI-2545-082299
6
O
11/05
相关PDF资料 |
PDF描述 |
|---|---|
| MIC37102BM | IC REG LDO ADJ 1A 8-SOIC |
| MIC2585-1MBTS TR | IC CTRLR HOT SWAP DUAL 24-TSSOP |
| GRM42A7U3F680JW31L | CAP CER 68PF 3.15KV 5% U2J 1808 |
| TOP270KG-TL | IC OFFLINE SW 60W 91W ESOP-12 |
| MIC2585-1MBTS | IC CTRLR HOT SWAP DUAL 24-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TOP243GN- | 制造商:POWERINT 制造商全称:Power Integrations, Inc. 功能描述:TOPSwitch-GX Family Extended Power, Design Flexible, EcoSmart, Integrated Off-line Switcher |
| TOP243GN-TL | 功能描述:交流/直流开关转换器 15W 85-265 VAC 25W 230 VAC RoHS:否 制造商:STMicroelectronics 输出电压:800 V 输入/电源电压（最大值）:23.5 V 输入/电源电压（最小值）:11.5 V 开关频率:115 kHz 电源电流:1.6 mA 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:SSO-10 封装:Reel |
| TOP243G-TL | 功能描述:IC OFFLINE SWIT OVP UVLO HV 8SMD RoHS:否 类别:集成电路 (IC) >> PMIC - AC-DC 转换器，离线开关 系列:TOPSwitch®-GX 标准包装:1 系列:FPS™ 输出隔离:隔离 频率范围:61kHz ~ 73kHz 输入电压:8 V ~ 26 V 输出电压:650V 功率（瓦特）:12W 工作温度:-40°C ~ 115°C 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-MDIP 包装:Digi-Reel® 其它名称:FSL206MRBNFSDKR |
| TOP243P | 功能描述:IC OFFLINE SWIT OVP UVLO HV 8DIP RoHS:否 类别:集成电路 (IC) >> PMIC - AC-DC 转换器，离线开关 系列:TOPSwitch®-GX 标准包装:1 系列:FPS™ 输出隔离:隔离 频率范围:61kHz ~ 73kHz 输入电压:8 V ~ 26 V 输出电压:650V 功率（瓦特）:12W 工作温度:-40°C ~ 115°C 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-MDIP 包装:Digi-Reel® 其它名称:FSL206MRBNFSDKR |
| TOP243P- | 制造商:POWERINT 制造商全称:Power Integrations, Inc. 功能描述:TOPSwitch-GX Family Extended Power, Design Flexible, EcoSmart, Integrated Off-line Switcher |
发布紧急采购，3分钟左右您将得到回复。