- 您现在的位置：买卖IC网 > PDF目录19730 > TOP254MN (Power Integrations)IC OFFLINE SWIT PROG OVP 10CSDIP PDF资料下载
参数资料
| 型号： | TOP254MN |
| 厂商： | Power Integrations |
| 文件页数： | 11/50页 |
| 文件大小： | 0K |
| 描述： | IC OFFLINE SWIT PROG OVP 10CSDIP |
| 产品培训模块： | TOPSwitch® HX General Introduction |
| 标准包装： | 50 |
| 系列： | TOPSwitch®-HX |
| 输出隔离： | 隔离 |
| 频率范围： | 119kHz ~ 145kHz |
| 输出电压： | 700V |
| 功率（瓦特）： | 62W |
| 工作温度： | -40°C ~ 150°C |
| 封装/外壳： | 10-SDIP（0.300"，7.62mm），9 引线 |
| 供应商设备封装： | SDIP-10C |
| 包装： | 管件 |
| 配用： | 596-1193-ND - KIT REF DESIGN TOP HX FOR TOP258 |
| 其它名称： | 596-1175-5 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页
TOP252-262
Line Overvoltage Shutdown (OV)
The same resistor used for UV also sets an overvoltage
threshold, which, once exceeded, will force TOPSwitch-HX to
stop switching instantaneously (after completion of the current
switching cycle). If this condition lasts for at least 100 m s, the
TOPSwitch-HX output will be forced into off state. Unlike with
TOPSwitch-GX, however, when the line voltage is back to
normal with a small amount of hysteresis provided on the OV
threshold to prevent noise triggering, the state machine sets to
S13 and forces TOPSwitch-HX to go through the entire auto-
restart sequence before attempting to switch again. The ratio
of OV and UV thresholds is preset at 4.5, as can be seen in
Figure 12. When the MOSFET is off, the rectified DC high
voltage surge capability is increased to the voltage rating of the
MOSFET (700 V), due to the absence of the reflected voltage
and leakage spikes on the drain. The OV feature can be
disabled independent of the UV feature.
In order to reduce the no-load input power of TOPSwitch-HX
designs, the V-pin (or M-pin for P Package) operates at very low
currents. This requires careful layout considerations when
designing the PCB to avoid noise coupling. Traces and
components connected to the V-pin should not be adjacent to
any traces carrying switching currents. These include the drain,
Voltage Monitor and External Current Limit Pin Table*
clamp network, bias winding return or power traces from other
converters. If the line sensing features are used, then the sense
resistors must be placed within 10 mm of the V-pin to minimize
the V-pin node area. The DC bus should then be routed to the
line sense resistors. Note that external capacitance must not
be connected to the V-pin as this may cause misoperation of
the V pin related functions.
Hysteretic or Latching Output Overvoltage Protection (OVP)
The detection of the hysteretic or latching output overvoltage
protection (OVP) is through the trigger of the line overvoltage
threshold. The V-pin or M-pin voltage will drop by 0.5 V, and
the controller measures the external attached impedance
immediately after this voltage drops. If I V or I M exceeds I OV(LS)
(336 m A typical) longer than 100 m s, TOPSwitch-HX will latch
into a permanent off state for the latching OVP. It only can be
reset if V V or V M goes below 1 V or V C goes below the power-
up-reset threshold (V C(RESET) ) and then back to normal.
If I V or I M does not exceed I OV(LS) or exceeds no longer than
100 m s, TOPSwitch-HX will initiate the line overvoltage and the
hysteretic OVP. Their behavior will be identical to the line
overvoltage shutdown (OV) that has been described in detail in
the previous section.
Figure Number
16
17
18
19
20
21
22
23
24
25
26
27
28
Three Terminal Operation
3
Line Undervoltage
Line Overvoltage
Line Feed-Forward (DC MAX )
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
Output Overvoltage Protection
Overload Power Limiting
3
3
3
External Current Limit
Remote ON/OFF
3
3
3
3
3
3
3
3
Device Reset
* This table is only a partial list of many VOLTAGE MONITOR and EXTERNAL CURRENT LIMIT Pin Configurations that are possible.
3
Table 2.
VOLTAGE MONITOR (V) Pin and EXTERNAL CURRENT LIMIT (X) Pin Configuration Options.
Multi-Function Pin Table*
Figure Number
29
30
31
32
33
34
35
36
37
38
39
40
Three Terminal Operation
3
Line Undervoltage
Line Overvoltage
Line Feed-Forward (DC MAX )
Output Overvoltage Protection
3
3
3
3
3
3
3
3
3
3
3
3
3
Overload Power Limiting
3
External Current Limit
Remote ON/OFF
3
3
3
3
3
3
3
Device Reset
* This table is only a partial list of many MULTI-FUNCTIONAL Pin Configurations that are possible.
3
Table 3.
MULTI-FUNCTION (M) Pin Configuration Options.
11
www.powerint.com
Rev. H 06/13
相关PDF资料 |
PDF描述 |
|---|---|
| VE-24K-CY-F3 | CONVERTER MOD DC/DC 40V 50W |
| M4A5-192/96-12VI | IC CPLD ISP 4A 192MC 144TQFP |
| MIC2585-2LBTS TR | IC CTRLR HOT SWAP DUAL 24-TSSOP |
| MIC2585-2LBTS | IC CTRLR HOT SWAP DUAL 24-TSSOP |
| M4A5-192/96-10VC | IC CPLD ISP 4A 192MC 144TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TOP254PG | 功能描述:交流/直流开关转换器 20W/30W PK 85-264VAC 28W/47W PK (230V AC) RoHS:否 制造商:STMicroelectronics 输出电压:800 V 输入/电源电压（最大值）:23.5 V 输入/电源电压（最小值）:11.5 V 开关频率:115 kHz 电源电流:1.6 mA 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:SSO-10 封装:Reel |
| TOP254PN | 功能描述:交流/直流开关转换器 Off-Line Switcher IC 20W/30W PK RoHS:否 制造商:STMicroelectronics 输出电压:800 V 输入/电源电压（最大值）:23.5 V 输入/电源电压（最小值）:11.5 V 开关频率:115 kHz 电源电流:1.6 mA 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:SSO-10 封装:Reel |
| TOP254YN | 功能描述:交流/直流开关转换器 Off-Line Switcher IC 43W RoHS:否 制造商:STMicroelectronics 输出电压:800 V 输入/电源电压（最大值）:23.5 V 输入/电源电压（最小值）:11.5 V 开关频率:115 kHz 电源电流:1.6 mA 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:SSO-10 封装:Reel |
| TOP255EG | 功能描述:交流/直流开关转换器 57W (85-264VAC) 81W (230V AC) RoHS:否 制造商:STMicroelectronics 输出电压:800 V 输入/电源电压（最大值）:23.5 V 输入/电源电压（最小值）:11.5 V 开关频率:115 kHz 电源电流:1.6 mA 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:SSO-10 封装:Reel |
| TOP255EN | 功能描述:交流/直流开关转换器 Int Off-Line Switchr 57/81W RoHS:否 制造商:STMicroelectronics 输出电压:800 V 输入/电源电压（最大值）:23.5 V 输入/电源电压（最小值）:11.5 V 开关频率:115 kHz 电源电流:1.6 mA 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:SSO-10 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。