- 您现在的位置：买卖IC网 > PDF目录98270 > TPA2005D1DGNG4 (TEXAS INSTRUMENTS INC) 1.45 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8 PDF资料下载
参数资料
| 型号： | TPA2005D1DGNG4 |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 音频／视频放大 |
| 英文描述： | 1.45 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
| 封装： | GREEN, PLASTIC, MSOP-8 |
| 文件页数： | 4/32页 |
| 文件大小： | 1128K |
| 代理商： | TPA2005D1DGNG4 |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
Input Resistors (RI)
Gain + 2
150 kW
R
I
(1)
Decoupling Capacitor (CS)
Input Capacitors (CI)
fc +
1
2p R
I
C
I
(2)
C
I +
1
2p R
I
fc
(3)
SLOS369F – JULY 2002 – REVISED JULY 2008............................................................................................................................................................... www.ti.com
Resistor matching is important in fully differential amplifiers. The balance of the output on the reference
voltage depends on matched ratios of the resistors. CMRR, PSRR, and cancellation of the second harmonic
distortion diminish if resistor mismatch occurs. Therefore, it is recommended to use 1% tolerance resistors or
better to keep the performance optimized. Matching is more important than overall tolerance. Resistor arrays with
1% matching can be used with a tolerance greater than 1%.
Place the input resistors close to the TPA2005D1 to limit noise injection on the high-impedance nodes.
For optimal performance the gain should be set to 2 V/V or lower. Lower gain allows the TPA2005D1 to operate
at its best, and keeps a high voltage at the input making the inputs less susceptible to noise.
The TPA2005D1 is a high-performance class-D audio amplifier that requires adequate power supply decoupling
to ensure the efficiency is high and total harmonic distortion (THD) is low. For higher frequency transients,
spikes, or digital hash on the line, a good low equivalent-series-resistance (ESR) ceramic capacitor, typically 1
F, placed as close as possible to the device V
DD lead works best. Placing this decoupling capacitor close to the
TPA2005D1 is important for the efficiency of the class-D amplifier, because any resistance or inductance in the
trace between the device and the capacitor can cause a loss in efficiency. For filtering lower-frequency noise
signals, a 10
F or greater capacitor placed near the audio power amplifier would also help, but it is not required
in most applications because of the high PSRR of this device.
The TPA2005D1 does not require input coupling capacitors if the design uses a differential source that is biased
from 0.5 V to VDD - 0.8 V (shown in Figure 32). If the input signal is not biased within the recommended
common-mode input range, if needing to use the input as a high pass filter (shown in Figure 33), or if using a
single-ended source (shown in Figure 34), input coupling capacitors are required.
The input capacitors and input resistors form a high-pass filter with the corner frequency, fc, determined in
equation Equation 2.
The value of the input capacitor is important to consider as it directly affects the bass (low frequency)
performance of the circuit. Speakers in wireless phones cannot usually respond well to low frequencies, so the
corner frequency can be set to block low frequencies in this application.
Equation Equation 3 is reconfigured to solve for the input coupling capacitance.
If the corner frequency is within the audio band, the capacitors should have a tolerance of 10% or better,
because any mismatch in capacitance causes an impedance mismatch at the corner frequency and below, and
causes pop. Any capacitor in the audio path should have a rating of X7R or better.
For a flat low-frequency response, use large input coupling capacitors (1
F). However, in a GSM phone the
ground signal is fluctuating at 217 Hz, but the signal from the codec does not have the same 217 Hz fluctuation.
The difference between the two signals is amplified, sent to the speaker, and heard as a 217 Hz hum.
12
Copyright 2002–2008, Texas Instruments Incorporated
Product Folder Link(s): TPA2005D1
相关PDF资料 |
PDF描述 |
|---|---|
| TPA2005D1DGNRG4 | 1.45 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
| TPA2006D1DRBR | 1.45 W, 1 CHANNEL, AUDIO AMPLIFIER, PQCC8 |
| TPA2006D1DRBT | 1.45 W, 1 CHANNEL, AUDIO AMPLIFIER, PQCC8 |
| TPA2006D1DRB | 1.45 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
| TPA2006D1DRBRG4 | 1.45 W, 1 CHANNEL, AUDIO AMPLIFIER, PQCC8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPA2005D1DGNR | 功能描述:音频放大器 Mono Fully Diff Filter-Free Class-D RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| TPA2005D1DGNRG4 | 功能描述:音频放大器 Mono Fully Diff Filter-Free Class-D RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| TPA2005D1DGNRQ1 | 功能描述:音频放大器 1.4W Class D Audio Power Amp RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| TPA2005D1DRBQ1 | 功能描述:音频放大器 1.4-W Mono Class-D Aud Power Amplifier RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| TPA2005D1DRBR | 功能描述:音频放大器 Mono Fully Diff Filter-Free Class-D RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。