- 您现在的位置：买卖IC网 > PDF目录98274 > TPA6011A4PWPG4 (TEXAS INSTRUMENTS INC) 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO24 PDF资料下载
参数资料
| 型号： | TPA6011A4PWPG4 |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 音频控制 |
| 英文描述： | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO24 |
| 封装： | GREEN, PLASTIC, HTSSOP-24 |
| 文件页数： | 19/35页 |
| 文件大小： | 744K |
| 代理商： | TPA6011A4PWPG4 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页
www.ti.com
V(LRMS)
VO
IDD
IDD(avg)
Efficiency of a BTL amplifier +
P
L
P
SUP
Where:
P
L +
V
Lrms
2
R
L
, and V
LRMS +
V
P
2
, therefore, P
L +
V
P
2
2R
L
and PSUP + VDD IDDavg
and
I
DDavg +
1
p
0
V
P
R
L
sin(t) dt
+
1
p
V
P
R
L
[cos(t)]
p
0 +
2V
P
p
R
L
Therefore,
P
SUP +
2 V
DD VP
p
R
L
(7)
Efficiency of a BTL amplifier +
V
P
2
2 R
L
2 V
DD VP
p
R
L
+
p
V
P
4 V
DD
PL = Power delivered to load
PSUP = Power drawn from power supply
VLRMS = RMS voltage on BTL load
RL = Load resistance
V
P +
2 P
L RL
hBTL +
p
2 P
L RL
4 V
DD
Where:
Therefore,
VP = Peak voltage on BTL load
IDDavg = Average current drawn from the power supply
VDD = Power supply voltage
ηBTL = Efficiency of a BTL amplifier
(8)
TPA6011A4
SLOS392A – FEBRUARY 2002 – REVISED JULY 2004
Figure 38. Voltage and Current Waveforms for BTL Amplifiers
Although the voltages and currents for SE and BTL are sinusoidal in the load, currents from the supply are very
different between SE and BTL configurations. In an SE application the current waveform is a half-wave rectified
shape, whereas in BTL it is a full-wave rectified waveform. This means RMS conversion factors are different.
Keep in mind that for most of the waveform both the push and pull transistors are not on at the same time, which
supports the fact that each amplifier in the BTL device only draws current from the supply for half the waveform.
The following equations are the basis for calculating amplifier efficiency.
substituting PL and PSUP into Equation 7,
Table 5 employs Equation 8 to calculate efficiencies for four different output power levels. Note that the efficiency
of the amplifier is quite low for lower power levels and rises sharply as power to the load is increased resulting in
a nearly flat internal power dissipation over the normal operating range. Note that the internal dissipation at full
output power is less than in the half power range. Calculating the efficiency for a specific system is the key to
proper power supply design. For a stereo 1-W audio system with 8-
loads and a 5-V supply, the maximum draw
on the power supply is almost 3.25 W.
26
相关PDF资料 |
PDF描述 |
|---|---|
| TPA6013A4PWPG4 | 2 CHANNEL(S), TONE CONTROL CIRCUIT, PDSO24 |
| TPA6013A4PWPRG4 | 2 CHANNEL(S), TONE CONTROL CIRCUIT, PDSO24 |
| TPA6017A2PWPR | 1.9 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO20 |
| TPA6017A2PWP | 1.9 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO20 |
| TPA6017A2PWPG4 | 1.9 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO20 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPA6011A4PWPR | 功能描述:音频放大器 Stereo Class-AB w/Ster Hdphn Drive RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| TPA6011A4PWPRG4 | 功能描述:音频放大器 Stereo Class-AB w/Ster Hdphn Drive RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| TPA6012A4 | 制造商:TI 制造商全称:Texas Instruments 功能描述:3-W STEREO AUDIO POWER AMPLIFIER WITH ADVANCED DC VOLUME CONTROL |
| TPA6012A4PWP | 功能描述:音频放大器 2W Stereo Audio Power Amp RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| TPA6012A4PWPEVM | 功能描述:音频 IC 开发工具 TPA6012A4PWP Eval Mod RoHS:否 制造商:Texas Instruments 产品:Evaluation Kits 类型:Audio Amplifiers 工具用于评估:TAS5614L 工作电源电压:12 V to 38 V |
发布紧急采购，3分钟左右您将得到回复。