- 您现在的位置：买卖IC网 > PDF目录98277 > TPA701DGNRG4 (TEXAS INSTRUMENTS INC) 0.7 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8 PDF资料下载
参数资料
| 型号： | TPA701DGNRG4 |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 音频／视频放大 |
| 英文描述： | 0.7 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
| 封装： | GREEN, PLASTIC, MSOP-8 |
| 文件页数： | 9/28页 |
| 文件大小： | 790K |
| 代理商： | TPA701DGNRG4 |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
TPA701
700-mW MONO LOW-VOLTAGE AUDIO POWER AMPLIFIER
SLOS229D – NOVEMBER1998 – REVISED MAY 2003
17
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
component selection (continued)
In this example, CI is 0.40 F, so one would likely choose a value in the range of 0.47 F to 1 F. A further
consideration for this capacitor is the leakage path from the input source through the input network (RI, CI) and
the feedback resistor (RF) to the load. This leakage current creates a dc offset voltage at the input to the amplifier
that reduces useful headroom, especially in high gain applications. For this reason a low-leakage tantalum or
ceramic capacitor is the best choice. When polarized capacitors are used, the positive side of the capacitor
should face the amplifier input in most applications, as the dc level there is held at VDD/2, which is likely higher
than the source dc level. It is important to confirm the capacitor polarity in the application.
power supply decoupling, CS
The TPA701 is a high-performance CMOS audio amplifier that requires adequate power supply decoupling to
ensure the output total harmonic distortion (THD) is as low as possible. Power supply decoupling also prevents
oscillations for long lead lengths between the amplifier and the speaker. The optimum decoupling is achieved
by using two capacitors of different types that target different types of noise on the power supply leads. For
higher frequency transients, spikes, or digital hash on the line, a good low equivalent-series-resistance (ESR)
ceramic capacitor, typically 0.1
F placed as close as possible to the device VDD lead works best. For filtering
lower-frequency noise signals, a larger aluminum electrolytic capacitor of 10
F or greater placed near the audio
power amplifier is recommended.
midrail bypass capacitor, CB
The midrail bypass capacitor, CB, is the most critical capacitor and serves several important functions. During
start-up or recovery from shutdown mode, CB determines the rate at which the amplifier starts up. The second
function is to reduce noise produced by the power supply caused by coupling into the output drive signal. This
noise is from the midrail generation circuit internal to the amplifier, which appears as degraded PSRR and
THD + N. The capacitor is fed from a 250-k
source inside the amplifier. To keep the start-up pop as low as
possible, the relationship shown in equation 10 should be maintained. This insures the input capacitor is fully
charged before the bypass capacitor is fully charged and the amplifier starts up.
(10)
10
C
B
250 k
v
1
R
F )
R
I
C
I
As an example, consider a circuit where CB is 2.2 F, CI is 0.47 F, RF is 50 k, and RI is 10 k. Inserting these
values into the equation 10 we get:
18.2
v 35.5
which satisfies the rule. Bypass capacitor, CB, values of 0.1 F to 2.2 F ceramic or tantalum low-ESR capacitors
are recommended for the best THD and noise performance.
using low-ESR capacitors
Low-ESR capacitors are recommended throughout this applications section. A real (as opposed to ideal)
capacitor can be modeled simply as a resistor in series with an ideal capacitor. The voltage drop across this
resistor minimizes the beneficial effects of the capacitor in the circuit. The lower the equivalent value of this
resistance, the more the real capacitor behaves like an ideal capacitor.
相关PDF资料 |
PDF描述 |
|---|---|
| TPA711D | 0.35 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
| TPA711DGN | 0.7 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
| TPA711DGNR | 0.7 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
| TPA711DR | 0.35 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
| TPA711DGNRG4 | 0.7 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPA701DR | 功能描述:音频放大器 700mW Lw V Audio RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| TPA701DRG4 | 功能描述:音频放大器 700-mW Low-Voltage RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| TPA701EVM | 制造商:TI 制造商全称:Texas Instruments 功能描述:700-mW MONO LOW-VOLTAGE AUDIO POWER AMPLIFIER |
| TPA701MSOPEVM | 功能描述:音频 IC 开发工具 TPA701MSOP Eval Mod RoHS:否 制造商:Texas Instruments 产品:Evaluation Kits 类型:Audio Amplifiers 工具用于评估:TAS5614L 工作电源电压:12 V to 38 V |
| TPA711 | 制造商:TI 制造商全称:Texas Instruments 功能描述:700-mW MONO LOW-VOLTAGE AUDIO POWER AMPLIFIER |
发布紧急采购，3分钟左右您将得到回复。