- 您现在的位置：买卖IC网 > PDF目录98277 > TPA721DRG4 (TEXAS INSTRUMENTS INC) 0.7 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8 PDF资料下载
参数资料
| 型号： | TPA721DRG4 |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 音频／视频放大 |
| 英文描述： | 0.7 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
| 封装： | GREEN, PLASTIC, MS-012AA, SOIC-8 |
| 文件页数： | 5/26页 |
| 文件大小： | 663K |
| 代理商： | TPA721DRG4 |
www.ti.com
RL
CC
VO(PP)
VDD
–3 dB
fc
BTL AMPLIFIER EFFICIENCY
VL(RMS)
VO
IDD
IDD(RMS)
TPA721
SLOS231E – NOVEMBER 1998 – REVISED JUNE 2004
APPLICATION INFORMATION (continued)
Figure 24. Single-Ended Configuration and Frequency Response
Increasing power to the load does carry a penalty of increased internal power dissipation. The increased
dissipation is understandable considering that the BTL configuration produces 4
× the output power of a SE
configuration. Internal dissipation versus output power is discussed further in the thermal considerations section.
The primary cause of linear amplifier inefficiencies is voltage drop across the output stage transistors. The
internal voltage drop has two components. One is the headroom or dc voltage drop that varies inversely to output
power. The second component is due to the sine-wave nature of the output. The total voltage drop can be
calculated by subtracting the RMS value of the output voltage from VDD. The internal voltage drop multiplied by
the RMS value of the supply current, IDD(RMS), determines the internal power dissipation of the amplifier.
An easy-to-use equation to calculate efficiency starts out being equal to the ratio of power from the power supply
to the power delivered to the load. To accurately calculate the RMS values of power in the load and in the
amplifier, the current and voltage waveform shapes must first be understood (see Figure 25).
Figure 25. Voltage and Current Waveforms for BTL Amplifiers
Although the voltages and currents for SE and BTL are sinusoidal in the load, currents from the supply are
different between SE and BTL configurations. In an SE application the current waveform is a half-wave rectified
shape whereas in BTL it is a full-wave rectified waveform. This means RMS conversion factors are different.
Keep in mind that for most of the waveform, both the push and pull transistors are not on at the same time, which
supports the fact that each amplifier in the BTL device only draws current from the supply for half the waveform.
The following equations are the basis for calculating amplifier efficiency.
13
相关PDF资料 |
PDF描述 |
|---|---|
| TPA731DGNR | 0.7 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
| TPA731DGN | 0.7 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
| TPA731DR | 0.35 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
| TPA731D | 0.35 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
| TPA731DG4 | 0.35 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPA721EVM | 制造商:TI 制造商全称:Texas Instruments 功能描述:700-mW MONO LOW-VOLTAGE AUDIO POWER AMPLIFIER |
| TPA721MSOPEVM | 功能描述:音频 IC 开发工具 TPA721MSOP Eval Mod RoHS:否 制造商:Texas Instruments 产品:Evaluation Kits 类型:Audio Amplifiers 工具用于评估:TAS5614L 工作电源电压:12 V to 38 V |
| TPA731 | 制造商:TI 制造商全称:Texas Instruments 功能描述:700-mW MONO LOW-VOLTAGE AUDIO POWER AMPLIFIER WITH DIFFERENTIAL INPUTS |
| TPA731_07 | 制造商:TI 制造商全称:Texas Instruments 功能描述:700-mW MONO LOW-VOLTAGE AUDIO POWER AMPLIFIER WITH DIFFERENTIAL INPUTS |
| TPA731D | 功能描述:音频放大器 700mW Low V RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。