- 您现在的位置：买卖IC网 > PDF目录69498 > TPD4124K BRUSHLESS DC MOTOR CONTROLLER, 3 A, PDIP26 PDF资料下载
参数资料
| 型号： | TPD4124K |
| 元件分类： | 运动控制电子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, 3 A, PDIP26 |
| 封装： | 13 X 32 MM, 2 MM PITCH, PLASTIC, DIP-26 |
| 文件页数： | 3/23页 |
| 文件大小： | 360K |
| 代理商： | TPD4124K |
TPD4124K
2008-11-26
11
External Parts
Typical external parts are shown in the following table.
Part
Typical
Purpose
Remarks
C1, C2, C3
25 V/2.2
μF
Bootstrap capacitor
(Note 1)
R1
0.35
Ω ± 1 % (1 W)
Current detection
(Note 2)
C4
25 V/10
μF
VCC power supply stability
(Note 3)
C5
25 V
/0.1 μF
VCC for surge absorber
(Note 3)
C6
25 V/1
μF
VREG power supply stability
(Note 3)
C7
25 V/1000 pF
VREG for surge absorber
(Note 3)
R2
5.1 k
Ω
DIAG pull-up resistor
(Note 4)
Note 1: The required bootstrap capacitance value varies according to the motor drive conditions. The capacitor is
biased by VCC and must be sufficiently derated for it.
Note 2: The following formula shows the detection current: IO = VR ÷ R1 (For VR = 0.5 V)
Do not exceed a detection current of 2 A when using this product.
(Please go from the outside in the over current protection.)
Note 3: When using this product, adjustment is required in accordance with the use environment. When mounting,
place as close to the base of this product leads as possible to improve the ripple and noise elimination.
Note 4: The DIAG pin is open drain. If not using the DIAG pin, connect to the GND.
Handling precautions
(1) Please control the input signal in the state to which the VCC voltage is steady. Both of the order of the VBB
power supply and the VCC power supply are not cared about either.
Note that if the power supply is switched off as described above, this product may be destroyed if the
current regeneration route to the VBB power supply is blocked when the VBB line is disconnected by a relay
or similar while the motor is still running.
(2) The RS pin connecting the current detection resistor is connected to a comparator in the IC and also
functions as a sensor pin for detecting over current. As a result, over voltage caused by a surge voltage, for
example, may destroy the circuit. Accordingly, be careful of handling the IC or of surge voltage in its
application environment.
相关PDF资料 |
PDF描述 |
|---|---|
| TPD7203F | BRUSHLESS DC MOTOR CONTROLLER, 1 A, PDSO24 |
| TPIC0107BDWP | BRUSH DC MOTOR CONTROLLER, 7.5 A, PDSO20 |
| TPIC0107BDWPR | BRUSH DC MOTOR CONTROLLER, 7.5 A, PDSO20 |
| TPIC43T02DAR | BRUSHLESS DC MOTOR CONTROLLER, PDSO38 |
| TPIC43T01DA | BRUSHLESS DC MOTOR CONTROLLER, PDSO38 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPD4124K(Q) | 功能描述:马达/运动/点火控制器和驱动器 Intelligent Power Device, 500V, 2A, BLDC motor drive, DIP26 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| TPD4125AK | 制造商:TOSHIBA 制造商全称:Toshiba Semiconductor 功能描述:Intelligent Power Device High Voltage Monolithic Silicon Power IC |
| TPD4125AK(Q) | 功能描述:马达/运动/点火控制器和驱动器 Intelligent Power Device, 500V, 3A, BLDC motor drive, DIP26 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| TPD4125K | 制造商:TOSHIBA 制造商全称:Toshiba Semiconductor 功能描述:Intelligent Power Device High Voltage Monolithic Silicon Power IC |
| TPD4125K(Q) | 功能描述:马达/运动/点火控制器和驱动器 Intelligent Power Device, 500V, 3A, BLDC motor drive, DIP26 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。