参数资料
型号: TPS2042BD
厂商: TEXAS INSTRUMENTS INC
元件分类: 电源管理
英文描述: 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8
封装: GREEN, PLASTIC, MS-012AA, SOIC-8
文件页数: 11/51页
文件大小: 1451K
代理商: TPS2042BD
GND
IN
EN1
EN2
OC1
OC2
OUT1
OUT2
TPS2042B
Rpullup
V+
www.ti.com
SLVS514K – JUNE 2010 – REVISED DECEMBER 2008
Figure 29. Typical Circuit for the OC Pin (Example, TPS2042B)
POWER DISSIPATION AND JUNCTION TEMPERATURE
The low on-resistance on the N-channel MOSFET allows the small surface-mount packages to pass large
currents. The thermal resistances of these packages are high compared to those of power packages; it is good
design practice to check power dissipation and junction temperature. Begin by determining the rDS(on) of the
N-channel MOSFET relative to the input voltage and operating temperature. As an initial estimate, use the
highest operating ambient temperature of interest and read rDS(on) from Figure 22. Using this value, the power
dissipation per switch can be calculated by:
PD = rDS(on) × I
2
Multiply this number by the number of switches being used. This step renders the total power dissipation from
the N-channel MOSFETs.
Finally, calculate the junction temperature:
TJ = PD × RqJA + TA
Where:
TA= Ambient temperature °C
RqJA = Thermal resistance
PD = Total power dissipation based on number of switches being used.
Compare the calculated junction temperature with the initial estimate. If they do not agree within a few degrees,
repeat the calculation, using the calculated value as the new estimate. Two or three iterations are generally
sufficient to get a reasonable answer.
THERMAL PROTECTION
Thermal protection prevents damage to the IC when heavy-overload or short-circuit faults are present for
extended periods of time. The TPS204xB/TPS205xB implements a thermal sensing to monitor the operating
junction temperature of the power distribution switch. In an overcurrent or short-circuit condition, the junction
temperature rises due to excessive power dissipation. Once the die temperature rises to approximately 140°C
due to overcurrent conditions, the internal thermal sense circuitry turns the power switch off, thus preventing the
power switch from damage. Hysteresis is built into the thermal sense circuit, and after the device has cooled
approximately 10°C, the switch turns back on. The switch continues to cycle in this manner until the load fault or
input power is removed. The OCx open-drain output is asserted (active low) when an overtemperature shutdown
or overcurrent occurs.
UNDERVOLTAGE LOCKOUT (UVLO)
An undervoltage lockout ensures that the power switch is in the off state at power up. Whenever the input
voltage falls below approximately 2 V, the power switch is quickly turned off. This facilitates the design of
hot-insertion systems where it is not possible to turn off the power switch before input power is removed. The
UVLO also keeps the switch from being turned on until the power supply has reached at least 2 V, even if the
switch is enabled. On reinsertion, the power switch is turned on, with a controlled rise time to reduce EMI and
voltage overshoots.
Copyright 2010–2008, Texas Instruments Incorporated
19
相关PDF资料
PDF描述
TPS2051BDG4 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8
TPS2041BDGNRG4 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8
TPS2054BDRG4 4-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16
TPS2043BDRG4 3-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16
TPS2053BD 3-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16
相关代理商/技术参数
参数描述
TPS2042BD 制造商:Texas Instruments 功能描述:IC PWR DIST SWITCH DUAL 8-SOIC
TPS2042BDG4 功能描述:电源开关 IC - USB Dual Current-Limited RoHS:否 制造商:Micrel 电源电压-最小:2.7 V 电源电压-最大:5.5 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:SOIC-8 封装:Tube
TPS2042BDGN 功能描述:电源开关 IC - USB Dual Current-Limited RoHS:否 制造商:Micrel 电源电压-最小:2.7 V 电源电压-最大:5.5 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:SOIC-8 封装:Tube
TPS2042BDGN 制造商:Texas Instruments 功能描述:DRIVER IC 制造商:Texas Instruments 功能描述:IC, CURRENT LIMITED POWER SW 5.5V MSOP-8
TPS2042BDGNG4 功能描述:电源开关 IC - USB Dual Current-Limited RoHS:否 制造商:Micrel 电源电压-最小:2.7 V 电源电压-最大:5.5 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:SOIC-8 封装:Tube