- 您现在的位置：买卖IC网 > PDF目录69502 > TPS2231PWPG4 (TEXAS INSTRUMENTS INC) 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO24 PDF资料下载
参数资料
| 型号： | TPS2231PWPG4 |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 电源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO24 |
| 封装： | GREEN, PLASTIC, HTSSOP-24 |
| 文件页数： | 11/40页 |
| 文件大小： | 1410K |
| 代理商： | TPS2231PWPG4 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
www.ti.com.................................................................................................................................................. SLVS536J – JULY 2004 – REVISED SEPTEMBER 2009
APPLICATION INFORMATION
INTRODUCTION TO ExpressCard
An ExpressCard module is an add-in card with a serial interface based on PCI Express and/or Universal Serial
Bus (USB) technologies. An ExpressCard comes in two form factors defined as ExpressCard|34 or
ExpressCard|54. The difference, as defined by the name, is the width of the module, 34 mm or 54 mm,
respectively. Host systems supporting the ExpressCard module can support either the ExpressCard|34 or
ExpressCard|54 or both.
ExpressCard POWER REQUIREMENTS
Regardless of which ExpressCard module is used, the power requirements as defined in the ExpressCard
Standard apply to both on an individual slot basis. The host system is required to supply 3.3 V, 1.5 V, and AUX
to each of the ExpressCard slots. However, the voltage is only applied after an ExpressCard is inserted into the
slot.
The ExpressCard connector has two pins, CPPE and CPUSB, that are used to signal the host when a card is
inserted. If the ExpressCard module itself connects the CPPE to ground, the logic low level on that signal
indicates to the host that a card supporting PCI Express has been inserted. If CPUSB is connected to ground,
then the ExpressCard module supports the USB interface. If both PCI Express and USB are supported by the
ExpressCard module, then both signals, CPPE and CPUSB, must be connected to ground.
In addition to the Card Present signals (CPPE and CPUSB), the host system determines when to apply power to
the ExpressCard module based on the state of the system. The state of the system is defined by the state of the
3.3 V, 1.5 V, and AUX input voltage rails. For the sake of simplicity, the 3.3-V and 1.5-V rails are defined as the
primary voltage rails as oppose to the auxiliary voltage rail, AUX.
ExpressCard POWER SWITCH OPERATION
The ExpressCard power switch resides on the host, and its main function is to control when to send power to the
ExpressCard slot. The ExpressCard power switch makes decisions based on the Card Present inputs and on the
state of the host system as defined by the primary and auxiliary voltage rails.
The following conditions define the operation of the host power controller:
1. When both primary power and auxiliary power at the input of the ExpressCard power switch are off, then all
power to the ExpressCard connector is off regardless of whether a card is present.
2. When both primary power and auxiliary power at the input of the ExpressCard power switch are on, then
power is only applied to the ExpressCard after the ExpressCard power switch detects that a card is present.
3. When primary power (either +3.3 V or +1.5 V) at the input of the ExpressCard power switch is off and
auxiliary power at the input of the ExpressCard power switch is on, then the ExpressCard power switch
behaves in the following manner:
(a) If neither of the Card Present inputs is detected (no card inserted), then no power is applied to the
ExpressCard slot.
(b) If the card is inserted after the system has entered this power state, then no power is applied to the
ExpressCard slot.
(c) If the card is inserted prior to the removal of the primary power (either +3.3 V or +1.5 V or both) at the
input of the ExpressCard power switch, then only the primary power (both +3.3 V and +1.5 V) is removed
and the auxiliary power is sent to the ExpressCard slot.
Figure 18 through Figure 23 illustrate the timing relationships between power/logic inputs and outputs of
ExpressCard.
Copyright 2004–2009, Texas Instruments Incorporated
19
相关PDF资料 |
PDF描述 |
|---|---|
| TPS2231PWPRG4 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO24 |
| TPS2236DAP | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO32 |
| TPS2231RGPT | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC20 |
| TPS2231PWG4 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO20 |
| TPS2231MRGPT | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC20 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPS2231PWPR | 功能描述:热插拔功率分布 Single Pwr Interface RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| TPS2231PWPRG4 | 功能描述:热插拔功率分布 Single Pwr Interface RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| TPS2231PWR | 功能描述:热插拔功率分布 Single Pwr Interface RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| TPS2231PWRG4 | 功能描述:热插拔功率分布 Single Pwr Interface RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| TPS2231RGPR | 功能描述:热插拔功率分布 Single Pwr Interface RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。