- 您现在的位置：买卖IC网 > PDF目录19743 > TPS2346PW (Texas Instruments)IC HOT SWAP POWER MGR 24-TSSOP PDF资料下载
参数资料
| 型号： | TPS2346PW |
| 厂商： | Texas Instruments |
| 文件页数： | 6/30页 |
| 文件大小： | 490K |
| 描述： | IC HOT SWAP POWER MGR 24-TSSOP |
| 标准包装： | 60 |
| 类型： | 热交换控制器 |
| 应用： | 光纤学网络（ONET） |
| 内部开关： | 无 |
| 电源电压： | -5.2V，3.3V，5V，5.15V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 24-TSSOP |
| 包装： | 管件 |
| 其它名称： | 296-12956-5 |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
TPS2346
SLUS529 MAY 2002
6
www.ti.com
pin descriptions
AGND: Analog ground reference for the device.
CPGND: Charge pump ground pin for the device.
CPUMP: Charge pump resevoir capacitor connection. An external capacitor of value 0.1 ?/SPAN>F to 1 ?/SPAN>F must be
connected between this pin and CPGND. The capacitor provides charge storage for the internal charge pump
for gate drive of the external N-channel FETs in line with the three positive-voltage loads.
CS1, CS2, CS3: These pins tie to the load side of the Channel 1, 2, and 3 current sense resistors, respectively.
They are used in conjunction with the VIN1, VIN2 and VIN3 inputs to provide load current magnitude information
to each of the positive rail LCAs.
CS4: This pin ties to the more positive side of the Channel 4 current sense resistor (common with the pass FET
source). It is used in conjunction with the VIN4 input to provide Channel 4 current magnitude information to the
negative rail LCA.
ENABLE
: Logic low enable input for back-end power. This pin ties to the module enable input at the plug-in
slot. When the input supplies are above the device minimums, and this pin is asserted low the TPS2346 begins
the sequential rampup of the back-end supplies. Pulling this input high (>2 V) turns off power to the back-end
planes, and puts the TPS2346 into low-power sleep mode.
GATE1, GATE2, GATE3, GATE4: Gate drive outputs for the Channel 1 through Channel 4 pass FETs,
respectively. The gates are driven according to the supply voltage, enable, sequence programming and load
current conditions of the add-in board.
IRAMP: Current ramp programming pin. A capacitor connected between this pin and ground determines the
maximum slew rate of the load current during ramp-up and ramp-down of the three positive back-end voltages.
This same capacitor is also used to establish the time limit for ramping each of the supply outputs.
PG
: Open-drain output asserted low to signal a back-end power-good condition. During a turn-on event, if each
of the load rails ramps up successfully to within the factory-programmed tolerances of the undervoltage (UV)
and overvoltage (OV) comparators, this output is subsequently asserted low. The output is false when back-end
power is not enabled, if any of the back-end voltages is not within its UV/OV window, as a result of an overcurrent
indication on any supply controller, or as a result of a fault timeout during linear ramp-up of any load voltage.
PRECHG: Bias supply of 1 V for bus signal precharge. During plug-in insertion and extraction events, this
output provides a bias supply that can be used to precharge the signal and control lines of the systems
address/data bus.
RGND: Reference ground input for the device.
VIN1: Channel 1 supply (5.15-V) input voltage sense. This pin is connected to the 5.15-V power supply input
to the add-in card. The supply potential is tested against the undervoltage limits prior to ramping voltage to the
back-end 5.15-V plane. The input supply also serves as the reference potential for the internally generated
current limit (IMAX) reference of the Channel 1 LCA. This pin also serves as the VCC supply for the TPS2346.
VIN2: Channel 2 supply (5-V) input voltage sense. This pin is connected to the 5-V power supply input to the
add-in card. The supply potential is tested against the undervoltage limits prior to ramping voltage to the
back-end 5-V plane. The input supply also serves as the reference potential for the internally generated current
limit (IMAX) reference of the Channel 2 LCA. This pin also serves as the supply input for the precharge bias
output.
VIN3: Channel 3 supply (3.3-V) input voltage sense. This pin is connected to the 3.3-V power supply input to
the add-in card. The supply potential is tested against the undervoltage limits prior to ramping voltage to the
back-end 3.3-V plane. The input supply also serves as the reference potential for the internally generated
current limit (IMAX) reference of the Channel 3 LCA.
相关PDF资料 |
PDF描述 |
|---|---|
| HSC31DRYH-S734 | CONN EDGECARD 62POS DIP .100 SLD |
| P-150SCS/A02 | BATTERY 1500MAH 1.2V SC NICAD |
| MIC29310-5.0BT | IC REG LDO 5V 3A TO-220-3 |
| LC5256MB-5F256I | IC XPLD 256MC 5NS 256FPBGA |
| GRM32NR72A823KA01L | CAP CER 0.082UF 100V X7R 1210 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPS2346PWR | 功能描述:热插拔功率分布 Optical Network Hot Swap Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| TPS2346PWRG4 | 功能描述:热插拔功率分布 Optical Network Hot Swap Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| TPS2350D | 功能描述:热插拔功率分布 Pwr Mngr for Redund -48V Supplies RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| TPS2350DG4 | 功能描述:热插拔功率分布 Pwr Mngr for Redund -48V Supplies RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| TPS2350DR | 功能描述:热插拔功率分布 Pwr Mngr for Redund -48V Supplies RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。