参数资料
| 型号： | TPS2371PWRG4 |
| 厂商： | Texas Instruments |
| 文件页数： | 14/19页 |
| 文件大小： | 0K |
| 描述： | IC PWR INTRFCE SW FOR POE 8TSSOP |
| 标准包装： | 2,000 |
| 应用： | 用于以太网供电（PoE）设备的电源接口开关 |
| 接口： | IEEE 802.3af |
| 封装/外壳： | 8-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 8-TSSOP |
| 包装： | 带卷 (TR) |
| 安装类型： | 表面贴装 |
TPS2371
SLUS566A JULY 2003 REVISED NOVEMBER 2003
4
www.ti.com
TERMINAL FUNCTIONS
TERMINAL
I/O
DESCRIPTION
NAME
NO.
I/O
DESCRIPTION
CLASS
2
O
Sets classification level with a single resistor to VEE. A precision voltage of 10.0 V is applied to this pin during
classification. RCLASS values listed in Table 1.
DELAY(2)
7
I
UVLO turn-off delay programming. Connect a capacitor between VCC and this pin to program the UVLO
turn-off delay.
DET
3
O
Connect the 24.9k
detection resistor (RDET) between this pin and VDD.
EN_DC
6
O
Ties to dc-to-dc converter’s shutdown or soft-start pin. Sinks 80
A until the load capacitor is fully charged.
ILIM(1)
1
O
Sets startup current limit level with a resistor to VEE. If using CDC2DCIN > 180 F, IRUSH must be less than
400 mA. Extra capacitance on ILIM pin can cause oscillations in the current waveform.
RTN
5
O
Return pin. Connect this pin to input return side of the dc-to-dc converter.
VDD
8
I
Connection to PD input port positive voltage.
VEE
4
I
Input side power return for the controller.
NOTE 1:
I
INRUSH + 450 mA *
25 k
W
R
LIM
(1A)
NOTE 2:
T
DELAY +
100 ms
mF
C
DELAY
DETAILED PIN DESCRIPTIONS
ILIM (Pin 1)
Inrush current limiting pin. This pin is used to program the inrush current of the device. Due to the low UVLO
hysteresis of this device, a 1.0-
F capacitor from this pin to VEE is necessary to allow startup with 20 in series
with VDD as required by the IEEE standards. By placing a resistor to VEE from this pin, the inrush current into
the load will be limited via the following equation:
I
INRUSH + 450 mA *
25 k
W
R
LIM
(1A)
CLASS (Pin 2)
Classification pin. The PD can be optionally classified by adding a resistor from this pin to ground. The resistor
specific to each class is given in Table 1: PoE Classification Resistance Values.
DET (Pin3)
Detection pin. This pin is used to set up the detection resistance during PD detection. By tying a resistor, RDET,
from this pin to VDD, the user sets the detection resistance. It should be noted that the device itself looks like
approximately 1 M
of resistance in parallel with RDET.
VEE (Pin 4)
Negative supply to the device.
RET (Pin 5)
Negative supply to the load. This pin is the drain side of a FET between the RET pin and the VEE pin, providing
hot swap capabilities to the load. When the FET is switched on, there is approximately 300m
between this
pin and VEE.
(1)
相关PDF资料 |
PDF描述 |
|---|---|
| TS3A24157RSERG4 | IC SWITCH DUAL SPDT 10UQFN |
| TS5A3159MDBVREP | IC SWITCH SPDT SOT23-6 |
| TS87C51RB2-MCB | IC MCU 8BIT 16K OTP 40MHZ 44PLCC |
| TSB42AC3PZT | IC LINK LAYER CTRLR 1394 100TQFP |
| TSB43AA82AIPGE | IC PHY LINK-LAYER CTRLR 144-LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPS2372-4RGWT | 功能描述:TPS2372 制造商:texas instruments 系列:* 包装:剪切带（CT） 零件状态:在售 封装/外壳:20-VQFN 裸露焊盘 供应商器件封装:20-VQFN（5x5） 标准包装:1 |
| TPS2373-4RGWT | 功能描述:IC POE CNTRL 20VQFN 制造商:texas instruments 系列:- 包装:剪切带（CT） 零件状态:在售 类型:控制器（PD） 通道数:1 功率 - 最大值:71W 内部开关:是 辅助作用:是 标准:802.3at（PoE+），802.3bt 电压 - 电源:0 V ~ 57 V 电流 - 电源:20mA 工作温度:-40°C ~ 125°C 封装/外壳:20-VQFN 裸露焊盘 供应商器件封装:20-VQFN（5x5） 标准包装:1 |
| TPS23750EVM-107 | 功能描述:电源管理IC开发工具 TPS23750 Eval Mod Buck RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| TPS23750EVM-108 | 功能描述:电源管理IC开发工具 TPS23750 Eval Mod Flyback RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| TPS23750PWP | 功能描述:热插拔功率分布 IEEE 802.3af PD Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。