- 您现在的位置：买卖IC网 > PDF目录69503 > TPS2377D-1 (TEXAS INSTRUMENTS INC) 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 PDF资料下载
参数资料
| 型号： | TPS2377D-1 |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 电源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| 封装： | GREEN, PLASTIC, SOIC-8 |
| 文件页数： | 3/25页 |
| 文件大小： | 623K |
| 代理商： | TPS2377D-1 |
Operational
Mode
Detection
Classification
PD Powered
Idle
1.4V
V(CL_ON)
V(CU_OFF)
V(CU_H)
V(UVLO_F)
V(UVLO_R)
V(VDD)
DETECTION
CLASSIFICATION
data sheet
www.ti.com ......................................................................................................................................................... SLVS570A – MARCH 2005 – REVISED APRIL 2008
Figure 17. Threshold Voltages
This feature of IEEE 802.3af eliminates powering and potentially damaging Ethernet devices not intended for
application of 48 V. When a voltage in the range of 2.7 V to 10.1 V is applied to the PI, an incremental resistance
of 25 k
signals the PSE that the PD is capable of accepting power. A PD that is capable of accepting power,
but is not ready, may present an incorrect signature intentionally. The incremental resistance is measured by
applying two different voltages to the PI and measuring the current it draws. These two test voltages must be
within the specified range and be at least 1 V apart. The incremental resistance equals the difference between
the voltages divided by the difference between the currents. The allowed range of resistance is 23.75 k
to
26.25 k
.
The TPS2375-1 is in detection mode whenever the supply voltage is below the lower classification threshold. The
TPS2375-1 draws a minimum of bias power in this condition, while PG and RTN are high impedance and the
circuits associated with ILIM and CLASS are disabled. The DET pin is pulled to ground during detection. Current
flowing through R(DET) to VSS (Figure 1) produces the detection signature. For most applications, a 24.9-k, 1%,
resistor is recommended. R(DET) can be a small, low-power resistor because it only sees a stress of about 5 mW.
When the input voltage rises above the 11.3 V lower classification comparator threshold, the DET pin goes to an
open-drain condition to conserve power.
The input diode bridge incremental resistance can be hundreds of ohms at the low currents seen at 2.7 V on the
PI. The bridge resistance is in series with R(DET) and increases the total resistance seen by the PSE. This varys
with the type of diode selected by the designer, and it is not usually specified on the diode data sheet. The value
of R(DET) may be adjusted downwards to accommodate a particular diode type.
Once the PSE has detected a PD, it may optionally classify the PD. This process allows a PSE to determine the
PD power requirements in order to allot only as much power as necessary from its fixed input power source. This
allows the PSE to power the maximum number of PDs from a particular power budget. This step is optional
because some PSEs can afford to allot the full power to every powered port.
The classification process applies a voltage between 14.5 V and 20.5 V to the input of the PD, which in turn
draws a fixed current set by R(CLASS). The PSE measures the PD current to determine which of the five available
classes (Table 1) that the PD is signalling. The total current drawn from the PSE during classification is the sum
of bias currents and current through R(CLASS). The TPS2375-1 disconnects R(CLASS) at voltages above the
classification range to avoid excessive power dissipation (Figure 16 and Figure 17).
requirements of the PD. The power rating of this resistor should be chosen so that it is not overstressed for the
required 75-ms classification period, during which 10 V is applied. The PD could be in classification for extended
periods during bench test conditions, or if an auxiliary power source with voltage within the classification range is
connected to the PD front end. Thermal protection may activate and turn classification off if it continues for more
than 75 ms, but the design must not rely on this function to protect the resistor.
Copyright 2005–2008, Texas Instruments Incorporated
11
Product Folder Link(s): TPS2375-1 TPS2377-1
相关PDF资料 |
PDF描述 |
|---|---|
| TPS2377DR-1G4 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| TPS2375PW-1 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| TPS2383BPMRG4 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQFP64 |
| TPS2383APMRG4 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQFP64 |
| TPS2383BPM | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQFP64 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPS2377D-1G4 | 功能描述:热插拔功率分布 IEEE 802.3af PoE Pwr Device Cntrler RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| TPS2377DG4 | 功能描述:热插拔功率分布 IEEE 802.3af PoE Pwr Device Cntrler RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| TPS2377DR | 功能描述:热插拔功率分布 IEEE 802.3af PoE Pwr Device Cntrler RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| TPS2377DR-1 | 功能描述:热插拔功率分布 IEEE 802.3af PoE Pwr Device Cntrler RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| TPS2377DR-1G4 | 功能描述:热插拔功率分布 IEEE 802.3af PoE Pwr Device Cntrler RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。