- 您现在的位置：买卖IC网 > PDF目录69503 > TPS2392DBT (TEXAS INSTRUMENTS INC) 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO44 PDF资料下载
参数资料
| 型号： | TPS2392DBT |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 电源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO44 |
| 封装： | GREEN, PLASTIC, SM-8, 44 PIN |
| 文件页数： | 17/33页 |
| 文件大小： | 596K |
| 代理商： | TPS2392DBT |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
TPS2392
TPS2393
SLUS536C AUGUST 2002 REVISED AUGUST 2004
www.ti.com
24
APPLICATION INFORMATION
using the PG output
The PG output is an indication of the load power status. PG is asserted after a load turn-on, once the load
voltage has ramped up to the input dc level, as indicated by a small VDS drop across the pass FET. The load
voltage is sensed by the DRAINSNS pin, which is connected to the pass FET drain through a small-signal
blocking diode. Also, the TPS2392 and TPS2393 first confirm that the full programmed sourcing current
(typically 40 mV/RSENSE) is available to the load electronics prior to declaring power good. The PG status is
latched once the power conditions are met, so that momentary current limiting operation due to input supply
transients is not reflected in this output status. This pin can be used to enable downstream converters, provide
a visual indication of load power good, or be level-translated or optocoupled to provide status reporting back
to the host controller.
When using PG to drive the enable input of a converter, care should be taken not to exceed the manufacturer’s
maximum voltage ratings for the pin. When asserted, the output driver pulls the PG pin to the VIN pin potential.
Because this status in latched, subsequent current limit operation of the circuit could result in pulling the enable
input below the brick’s VIN potential during the fault timeout period. If the brick does not provide an internal
clamp on this pin, a diode can be connected as shown in Figure 28 to externally limit the swing below VIN.
In either case, a resistor (R7 in Figure 28) should be used to limit the current pulled from this pin, protecting
both the converter and the PG output. R7 should be large enough to limit the PG input current to less than
10 mA, while still allowing the brick enable to be pulled below its maximum VIL threshold.
10
A
UDG20177
GATE
ISENS
DRNSNS
RSENSE
VOUT+
VOUT
VIN+
VIN
DC/DC
CONVERTER
Q1
VIN
D1
BAS19
RTN
D3
VDD
R7
43 k
TPS2392*
TPS2393*
CIN
EN
48 V
GND
PG
*Additional details omitted for clarity.
See block diagram on page 15 and 16 for pinout.
Figure 29. TPS2392/TPS2393 Active-Low Converter Enable
相关PDF资料 |
PDF描述 |
|---|---|
| TPS2393PWG4 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO14 |
| TPS2392PW | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO14 |
| TPS2393PWR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO14 |
| TPS2393PWRG4 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO14 |
| TPS2400DBVT | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPS2392EVM | 功能描述:电源管理IC开发工具 Simple -48V Hot Swap Contr EVM RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| TPS2392PW | 功能描述:热插拔功率分布 Full Featured -48V Industral Temp. RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| TPS2392PWG4 | 功能描述:热插拔功率分布 Full Featured -48V Industral Temp. RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| TPS2392PWR | 功能描述:热插拔功率分布 Full Featured -48V Industral Temp. RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| TPS2392PWRG4 | 功能描述:热插拔功率分布 Full Featured -48V Industral Temp. RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。