参数资料
型号: TPS2411PWG4
厂商: TEXAS INSTRUMENTS INC
元件分类: 模拟信号调理
英文描述: SPECIALTY ANALOG CIRCUIT, PDSO14
封装: GREEN, PLASTIC, TSSOP-14
文件页数: 5/31页
文件大小: 1020K
代理商: TPS2411PWG4
TPS2410 vs TPS2411 – MOSFET CONTROL METHODS
www.ti.com .................................................................................................................................................. SLVS727C – NOVEMBER 2006 – REVISED JUNE 2009
The operation of the two parts is summarized in Table 2.
Table 2. Operation as a Function of VAC
Turnoff Threshold(1)
≤ VAC ≤ 10 mV
V(AC) ≤ Turnoff Threshold
(1)
V(AC) > 10 mV
(MOSFET
V(AC) Forced < 10 mV
rDS(on) × ILOAD) ≤ 10 mV
Weak GATE pull-down
TPS2410 Strong GATE pull-down (OFF)
V(AC) regulated to 10 mV
GATE pulled high (ON)
(OFF)
TPS2411 Strong GATE pull-down (OFF)
Depends on previous state
GATE pulled high (ON)
(Hysteresis region)
(1)
Turnoff threshold is established by the value of RSET.
The TPS2410 control method yields several benefits. First, the low current GATE driver provides a gentle turn-on
and turn-off for slowly rising and falling input voltage. Second, it reduces the tendency for on/off cycling of a
comparator based solution at light loads. Third, it avoids reverse currents if the fast turn-off threshold is left
positive. The drawback to this method is that the MOSFET appears to have a high resistance at light load when
the regulation is active. A momentary output voltage droop occurs when a large step load is applied from a
light-load condition. The TPS2410 is a better solution for a mid-rail bus that will be re-regulated.
The TPS2411 turns the MOSFET on if V(AC) is greater than 10 mV, and hard off when V(AC) is less than the
RSET programmed threshold. There is no linear control range and slow turn-off. The disadvantage is that the
turn-off threshold must be negative (unless a specified load is always present) permitting a continuous reverse
current. Under a dynamic reverse voltage fault, the lower threshold voltage may permit a higher peak reverse
current. There are a number of advantages to this control method. Step loads from a light load condition are
handled without a voltage droop beyond I × R. If the redundant converter fails, applications with redundant
synchronous converters may permit a small amount of reverse current at light load in order to assure that the
MOSFET is all ready on. The TPS2411 is a better solution for low-voltage busses that will not be re-regulated,
and that may see large load steps transients.
These applications recommendations are meant as a starting point, with the needs of specific implementations
over-riding them.
Copyright 2006–2009, Texas Instruments Incorporated
13
Product Folder Link(s): TPS2410 TPS2411
相关PDF资料
PDF描述
TPS2412PWR SPECIALTY ANALOG CIRCUIT, PDSO8
TPS2412DG4 SPECIALTY ANALOG CIRCUIT, PDSO8
TPS2413D SPECIALTY ANALOG CIRCUIT, PDSO8
TPS2413PWR SPECIALTY ANALOG CIRCUIT, PDSO8
TPS2420RSAR 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC16
相关代理商/技术参数
参数描述
TPS2411PWR 功能描述:热插拔功率分布 N+1 OR-ing Pwr Rail Cntrlr RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
TPS2411PWRG4 功能描述:热插拔功率分布 N+1 and OR-ing Pwr Rail Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
TPS2412D 功能描述:热插拔功率分布 N+1/ORing Power Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
TPS2412DG4 功能描述:热插拔功率分布 N+1/ORing Pwr Cntrlr RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
TPS2412DR 功能描述:热插拔功率分布 N+1/ORing Power Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube