- 您现在的位置：买卖IC网 > PDF目录98280 > TPS2541RTET (TEXAS INSTRUMENTS INC) 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC16 PDF资料下载
参数资料
| 型号： | TPS2541RTET |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 电源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC16 |
| 封装： | GREEN, PLASTIC, WQFN-16 |
| 文件页数： | 17/37页 |
| 文件大小： | 999K |
| 代理商： | TPS2541RTET |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页
SLVSAG2A
– OCTOBER 2010 – REVISED APRIL 2011
Standard Downstream Port (SDP) USB 2.0
An SDP is a traditional USB port that follows USB 2.0 and supplies a minimum of 500 mA per port. USB 2.0
communications is supported, and the host controller must be active to allow charging.
Charging Downstream Port (CDP)
A CDP is a USB port that follows USB 2.0 BC1.2 and supplies a minimum of 1.5 A per port. It provides power
and meets USB 2.0 requirements for device enumeration. USB 2.0 communications is supported, and the host
controller must be active to allow charging. What separates a CDP from an SDP is the host-charge handshaking
logic that identifies this port as a CDP. A CDP is identifiable by a compliant BC1.2 client device and allows for
additional current draw by the client device.
The CDP hand-shaking process is two steps. During step one the portable equipment outputs a nominal 0.6 V
output on its D+ line and reads the voltage input on its D- line. The portable device concludes it is connected to
an SDP if the voltage is less than the nominal data detect voltage of 0.3 V. The portable device concludes that it
is connected to a Charging Port if the D- voltage is greater than the nominal data detect voltage of 0.3V and less
than 0.8 V.
The second step is necessary for portable equipment to determine between a CDP and a DCP. The portable
device outputs a nominal 0.6 V output on its D- line and reads the voltage input on its D+ line. The portable
device concludes it is connected to a CDP if the data line being read remains less than the nominal data detect
voltage of 0.3 V. The portable device concludes it is connected to a DCP if the data line being read is greater
than the nominal data detect voltage of 0.3V and less than 0.8 V.
Dedicated Charging Port (DCP)
A DCP is a special type of wall-adapter used in charging applications that uses a micro-B connector to connect
to portable devices. A DCP only provides power and cannot enumerate upstream facing portable equipment. It
does not support USB 2.0 communications, but it does provide specific impedances on the data lines reserved
for USB 2.0 so that it is identifiable as a dedicated charger.
The impedances presented on D+ and D- are different depending on the specific standard the dedicated charger
is designed to. BC1.2 and the Chinese Telecommunications Industry Standard YD/T 1591-2009 define that the
D+ and D- data lines should be shorted together with a maximum series impedance of 200
Ω.
On the other hand, with the divider mode, 2 V and 2.7 V are presented on D+ and on D-.
The TPS2540/40A/41 integrates an auto-detect feature that supports both DCP schemes. It starts in Divider
Mode. If a BC1.2 -compliant device is attached, the TPS2540/40A/41 responds by discharging OUT, turning back
ON the power switch and operating in BC1.2 DCP mode. It then stays in that mode until the device is
unattached, in which case it goes back to Divider Mode.
High-Bandwidth Data Line Switch
The TPS2540/40A/41 passes the D+ and D- data lines through the device to enable monitoring and handshaking
while supporting charging operation. A wide bandwidth signal switch is used, allowing data to pass through the
device without corrupting signal integrity. The data line switches are turned on in any of CDP or SDP operating
modes. The EN (or DSC if TPS2541) input also needs to be at logic High for the data line switches to be
enabled.
NOTE
1. While in CDP mode, the data switches are ON even while CDP handshaking is occurring.
2. The data line switches are OFF if EN (or DSC) is low, or if in DCP mode (BC1.2, Divider mode
or Auto-detect). They are not automatically turned off if the power switch (IN to OUT) is doing
current limiting. With TPS2540/40A, the data line switches are also off when in
“000” mode.
3. The data switches are for USB 2.0 differential pair only. In the case of a USB 3.0 host, the
super speed differential pairs must be routed directly to the USB connector without passing
through the TPS2540/40A/41.
24
Copyright
2010–2011, Texas Instruments Incorporated
相关PDF资料 |
PDF描述 |
|---|---|
| TPS2550DBV | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO6 |
| TPS2551DRVR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO6 |
| TPS2551DRVTG4 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO6 |
| TPS2551DRVRG4 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO6 |
| TPS2551DBVR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPS2543EVM-064 | 功能描述:电源管理IC开发工具 TPS2543 Eval Mod RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| TPS2543QRTERQ1 | 制造商:Texas Instruments 功能描述: 制造商:Texas Instruments 功能描述:IC CHARGING CTLR USB 16-WQFN 制造商:Texas Instruments 功能描述:USB charging controller w/ power switch |
| TPS2543QRTETQ1 | 功能描述:电源开关 IC - USB Auto USB Chrg Port Pwr Switch & Cntlr RoHS:否 制造商:Micrel 电源电压-最小:2.7 V 电源电压-最大:5.5 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:SOIC-8 封装:Tube |
| TPS2543RTER | 功能描述:电源开关 IC - USB USB Charging Port Pwr Sw & Cntrlr RoHS:否 制造商:Micrel 电源电压-最小:2.7 V 电源电压-最大:5.5 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:SOIC-8 封装:Tube |
| TPS2543RTET | 功能描述:电源开关 IC - USB USB Charging Port Pwr Sw & Cntrlr RoHS:否 制造商:Micrel 电源电压-最小:2.7 V 电源电压-最大:5.5 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:SOIC-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。