- 您现在的位置：买卖IC网 > PDF目录69508 > TPS40003DGQG4 (TEXAS INSTRUMENTS INC) SWITCHING CONTROLLER, 700 kHz SWITCHING FREQ-MAX, PDSO10 PDF资料下载
参数资料
| 型号： | TPS40003DGQG4 |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING CONTROLLER, 700 kHz SWITCHING FREQ-MAX, PDSO10 |
| 封装： | PLASTIC, MSOP-10 |
| 文件页数： | 27/27页 |
| 文件大小： | 663K |
| 代理商： | TPS40003DGQG4 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页
TPS40000, TPS40001
TPS40002, TPS40003
TPS40004, TPS40005
SLUS507D JANUARY 2002 REVISED NOVEMBER 2005
9
www.ti.com
APPLICATION INFORMATION
error amplifier
The error amplifier has a bandwidth of greater than 5 MHz, with open loop gain of at least 55 dB. The COMP
output voltage is clamped to a level above the oscillator ramp in order to improve large-scale transient response.
oscillator
The oscillator uses an internal resistor and capacitor to set the oscillation frequency. The ramp waveform is a
triangle at the PWM frequency with a peak voltage of 1.25 V, and a valley of 0.25 V. The PWM duty cycle is limited
to a maximum of 95%, allowing the bootstrap capacitor to charge during every cycle.
bootstrap/charge pump
There is an internal switch between VDD and BOOT. This switch charges the external bootstrap capacitor for
the floating supply. If the resistance of this switch is too high for the application, an external schottky diode
between VDD and BOOT can be used. The peak voltage on the bootstrap capacitor is approximately equal to
VDD.
driver
The HDRV and LDRV MOSFET drivers are capable of driving gate-to-source voltages up to 5.5 V. At VIN, = 5 V
and using appropriate MOSFETs, a 20-A converter can be achieved. The LDRV driver switches between VDD
and ground, while the HDRV driver is referenced to SW and switches between BOOT and SW. The maximum
voltage between BOOT and SW is 5.5 V.
synchronous rectification and predictive delay
In a normal buck converter, when the main switch turns off, current is flowing to the load in the inductor. This
current cannot be stopped immediately without using infinite voltage. For the current path to flow and maintain
voltage levels at a safe level, a rectifier or catch device is used. This device can be either a conventional diode,
or it can be a controlled active device if a control signal is available to drive it. The TPS4000x provides a signal
to drive an N-channel MOSFET as a rectifier. This control signal is carefully coordinated with the drive signal
for the main switch so that there is minimum delay from the time that the rectifier MOSFET turns off and the main
switch turns on, and minimum delay from when the main switch turns off and the rectifier MOSFET turns on.
This scheme, Predictive Gate Drive
t delay, uses information from the current switching cycle to adjust the
delays that are to be used in the next cycle. Figure 2 shows the switch-node voltage waveform for a
synchronously rectified buck converter. Illustrated are the relative effects of a fixed-delay drive scheme
(constant, pre-set delays for the turn-off to turn-on intervals), an adaptive delay drive scheme (variable delays
based upon voltages sensed on the current switching cycle) and the predictive delay drive scheme.
Note that the longer the time spent in diode conduction during the rectifier conduction period, the lower the
efficiency. Also, not described in Figure 2 is the fact that the predictive delay circuit can prevent the body diode
from becoming forward biased at all while at the same time avoiding cross conduction or shoot through. This
results in a significant power savings when the main MOSFET turns on, and minimizes reverse recovery loss
in the body diode of the rectifier MOSFET.
相关PDF资料 |
PDF描述 |
|---|---|
| TPS40020PWP | 0.01 A SWITCHING CONTROLLER, 1100 kHz SWITCHING FREQ-MAX, PDSO16 |
| TPS40020PWPG4 | 0.01 A SWITCHING CONTROLLER, 1100 kHz SWITCHING FREQ-MAX, PDSO16 |
| TPS40021PWPR | 0.01 A SWITCHING CONTROLLER, 1100 kHz SWITCHING FREQ-MAX, PDSO16 |
| TPS40020PWPR | 0.01 A SWITCHING CONTROLLER, 1100 kHz SWITCHING FREQ-MAX, PDSO16 |
| TPS40021PWP | 0.01 A SWITCHING CONTROLLER, 1100 kHz SWITCHING FREQ-MAX, PDSO16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPS40003DGQR | 功能描述:电压模式 PWM 控制器 Lo Input Vltg Mode Synch Buck Cntrlr RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| TPS40003DGQRG4 | 功能描述:电压模式 PWM 控制器 Lo Input Vltg Mode Synch Buck Cntrlr RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| TPS40004 | 制造商:TI 制造商全称:Texas Instruments 功能描述:LOW-INPUT VOLTAGE-MODE SYNCHRONOUS BUCK CONTROLLER |
| TPS40004DGQ | 功能描述:电压模式 PWM 控制器 Lo Input 300kHz Freq Synch Buck Cntrlr RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| TPS40004DGQG4 | 功能描述:电压模式 PWM 控制器 Lo Input 300kHz Freq Synch Buck Cntrlr RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。