- 您现在的位置：买卖IC网 > PDF目录69508 > TPS40050PWP (TEXAS INSTRUMENTS INC) 0.2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 PDF资料下载
参数资料
| 型号： | TPS40050PWP |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 稳压器 |
| 英文描述： | 0.2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封装： | GREEN, PLASTIC, HTSSOP-16 |
| 文件页数： | 32/36页 |
| 文件大小： | 648K |
| 代理商： | TPS40050PWP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页当前第32页第33页第34页第35页第36页
TPS40050
TPS40051
TPS40053
SLUS540F DECEMBER 2002 REVISED JUNE 2004
www.ti.com
5
TERMINAL FUNCTIONS
TERMINAL
I/O
DESCRIPTION
NAME
NO.
I/O
DESCRIPTION
BOOST
14
O
Gate drive voltage for the high side N-channel MOSFET. The BOOST voltage is 9 V greater than the input voltage.
A 0.1-
F ceramic capacitor should be connected from this pin to the drain of the lower MOSFET.
BP5
3
O
5-V reference. This pin should be bypassed to ground with a 0.1-
F ceramic capacitor. This pin may be used with
an external DC load of 1 mA or less.
BP10
11
O
10-V reference used for gate drive of the N-channel synchronous rectifier. This pin should be bypassed by a 1-
F
ceramic capacitor. This pin may be used with an external DC load of 1 mA or less.
COMP
8
O
Output of the error amplifier, input to the PWM comparator. A feedback network is connected from this pin to the
VFB pin to compensate the overall loop. The comp pin is internally clamped above the peak of the ramp to improve
large signal transient response.
HDRV
13
O
Floating gate drive for the high-side N-channel MOSFET. This pin switches from BOOST (MOSFET on) to SW
(MOSFET off).
ILIM
16
I
Current limit pin, used to set the overcurrent threshold. An internal current sink from this pin to ground sets a voltage
drop across an external resistor connected from this pin to VCC. The voltage on this pin is compared to the voltage
drop (VIN SW) across the high side MOSFET during conduction.
KFF
1
I
A resistor is connected from this pin to VIN to program the amount of voltage feed-forward. The current fed into
this pin is internally divided and used to control the slope of the PWM ramp.
LDRV
10
O
Gate drive for the N-channel synchronous rectifier. This pin switches from BP10 (MOSFET on) to ground
(MOSFET off).
PGND
9
Power ground reference for the device. There should be a low-impedance path from this pin to the source(s) of
the lower MOSFET(s).
RT
2
I
A resistor is connected from this pin to ground to set the internal oscillator and switching frequency.
SGND
5
Signal ground reference for the device.
SS/SD
6
I
Soft-start programming pin. A capacitor connected from this pin to ground programs the soft-start time. The
capacitor is charged with an internal current source of 2.3
A. The resulting voltage ramp on the SS pin is used
as a second non-inverting input to the error amplifier. The output voltage begins to rise when VSS/SD is
approximately 0.85 V. The output continues to rise and reaches regulation when VSS/SD is approximately 1.55 V.
The controller is considered shut down when VSS/SD is 125 mV or less. All internal circuitry is inactive. The internal
circuitry is enabled when VSS/SD is 210 mV or greater. When VSS/SD is less than approximately 0.85 V, the outputs
cease switching and the output voltage (VOUT) decays while the internal circuitry remains active.
SW
12
I
This pin is connected to the switched node of the converter and used for overcurrent sensing. The TPS40050 and
TPS40053 versions use this pin for zero current sensing as well.
SYNC
4
I
Syncronization input for the device. This pin can be used to synchronize the oscillator to an external master
frequency. If synchronization is not used, connect this pin to SGND.
VFB
7
I
Inverting input to the error amplifier. In normal operation the voltage on this pin is equal to the internal reference
voltage, 0.7 V.
VIN
15
I
Supply voltage for the device.
相关PDF资料 |
PDF描述 |
|---|---|
| TPS40050PWPG4 | 0.2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| TPS40051PWPR | 0.2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| TPS40053PWPG4 | 0.2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| TPS40053PWP | 0.2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| TPS40053PWPRG4 | 0.2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPS40050PWPG4 | 功能描述:DC/DC 开关控制器 Wide Input Vltg Synch Buck Cntrlr RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| TPS40050PWPR | 功能描述:DC/DC 开关控制器 Wide Input Vltg Synch Buck Cntrlr RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| TPS40050PWPRG4 | 功能描述:DC/DC 开关控制器 Wide Input Vltg Synch Buck Cntrlr RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| TPS40050-Q1 | 制造商:TI 制造商全称:Texas Instruments 功能描述:WIDE-INPUT SYNCHRONOUS BUCK CONTROLLER |
| TPS40050QPWPRQ1 | 功能描述:DC/DC 开关控制器 Auto Cat Wide-Input Synch Buck RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。