- 您现在的位置：买卖IC网 > PDF目录69510 > TPS51513RHB (TEXAS INSTRUMENTS INC) SWITCHING CONTROLLER, PQCC32 PDF资料下载
参数资料
| 型号： | TPS51513RHB |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING CONTROLLER, PQCC32 |
| 封装： | 5 X 5 MM, GREEN, PLASTIC, QFN-32 |
| 文件页数： | 11/38页 |
| 文件大小： | 1159K |
| 代理商： | TPS51513RHB |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
P P
I
25 A
0.2
5 A
-
=
=
P P
V
dT
L
I
-
=
P P
SAT
INST
I
1.2
41.5 A
2
-
=
+
=
÷
è
www.ti.com
SLUS956A – JUNE 2009 – REVISED FEBRUARY 2010
APPLICATION INFORMATION
Design Procedure
The TPS51513 has a simple design procedure for a high-performance controller.
Initial Parameters:
Step One: Determine the load requirements. For the purposes of this exercise, the following requirements are
used:
The processor requirements provide the following key parameters:
1. VMAX = 1.050 V
2. RL-L = –3 m
3. IMAX = 22 A; IOCP_MIN = 25 A
4. IDYN-MAX = 10 A
5. Sleep slew rate = 5 mV/ms (minimum)
Step Two: Determine system parameters. The input voltage range and operating frequency are of primary
interest. For example:
1. VIN-MAX = 15 V
2. VIN-MIN = 8 V
3. f = 300 kHz
For an operating frequency of 350 kHz, tie TONSEL to 3.3 V.
Step Three: Determine current sensing method. The TPS51513 supports both resistor sensing and inductor
DCR sensing. Inductor DCR sensing is chosen.
For resistor sensing, substitute the resistor value (1 m
recommended for a approximately 25-A application) for
RCS in the subsequent equations and skip Step Five.
Step Four: Determine inductor value and choose inductor. Smaller values of inductor have better transient
performance but higher ripple and lower efficiency. Higher values have the opposite characteristics. It is common
practice to limit the ripple current to 20% to 40% of the maximum current per phase. In this case, we use 20%:
IP-P = 25 A × 0.2 = 5 A
At f = 350 kHz, with 15-V input and 1.05-V output:
where
V = VIN-MAX – VMAX
dT = VMAX (F × VIN-MAX).
(8)
where
L = 0.6 mH
(9)
An inductor value of 0.6 mH is chosen. The inductor must not saturate during peak loading conditions. The factor
of 1.2 is to allow for current sensing and current limiting tolerances.
(10)
Copyright 2009–2010, Texas Instruments Incorporated
19
Product Folder Link(s) :TPS51513
相关PDF资料 |
PDF描述 |
|---|---|
| TPS53124RGET | DUAL SWITCHING CONTROLLER, PQCC24 |
| TPS53124PW | DUAL SWITCHING CONTROLLER, PDSO28 |
| TPS53124PWR | DUAL SWITCHING CONTROLLER, PDSO28 |
| TPS53125PW | DUAL SWITCHING CONTROLLER, 350 kHz SWITCHING FREQ-MAX, PDSO24 |
| TPS53125PWR | DUAL SWITCHING CONTROLLER, 350 kHz SWITCHING FREQ-MAX, PDSO24 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPS51513RHBR | 功能描述:DC/DC 开关控制器 3-28V Input Sync. Step Down Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| TPS51513RHBT | 功能描述:DC/DC 开关控制器 3-28V Input Sync. Step Down Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| TPS51513RHBT | 制造商:Texas Instruments 功能描述:Controller IC |
| TPS51518RUKR | 功能描述:DC/DC 开关控制器 Sgl Phase DCAP & D-CAP2 Cntrlr RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| TPS51518RUKT | 功能描述:DC/DC 开关控制器 Sgl Phase DCAP & D-CAP2 Cntrlr RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。