- 您现在的位置：买卖IC网 > PDF目录68613 > TPS54316QPWPRQ1 (TEXAS INSTRUMENTS INC) 7.5 A SWITCHING REGULATOR, 762 kHz SWITCHING FREQ-MAX, PDSO20 PDF资料下载
参数资料
| 型号： | TPS54316QPWPRQ1 |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 稳压器 |
| 英文描述： | 7.5 A SWITCHING REGULATOR, 762 kHz SWITCHING FREQ-MAX, PDSO20 |
| 封装： | GREEN, PLASTIC, HTSSOP-20 |
| 文件页数： | 5/19页 |
| 文件大小： | 0K |
| 代理商： | TPS54316QPWPRQ1 |
TPS54311-Q1, TPS54312-Q1
TPS54313-Q1, TPS54314-Q1
TPS54315-Q1, TPS54316-Q1
SGLS242G OCTOBER 2004 REVISED SEPTEMBER 2008
www.ti.com
13
Table 1. Summary of the Frequency Selection
Configurations
SWITCHING
FREQUENCY
FSEL PIN
RT PIN
350 kHz, internally
set
Float or AGND
Float
550 kHz, internally
set
≥ 2.5 V
Float
Externally set 280
kHz to 700 kHz
Float
R = 68 k to 180 k
Externally
synchronized
frequency(1)
Synchronization
signal
R = RT value for 80% of
external synchronization
frequency
(1) To ensure proper operation when RC filter is used between external
clock and FSEL pin, the recommended values are R
≤ 1k and
C
≤ 68 pF.
Error Amplifier
The high performance, wide bandwidth, voltage error
amplifier is gain limited to provide internal compensation
of the control loop. The user is given limited flexibility in
choosing output L and C filter components. Inductance
values of 4.7
H to 10 H are typical and available from
several vendors. The resulting designs exhibit good noise
and ripple characteristics, along with exceptional transient
response. Transient recovery times are typically in the
range of 10 to 20
s.
PWM Control
Signals from the error amplifier output, oscillator, and
current limit circuit are processed by the PWM control
logic. Referring to the internal block diagram, the control
logic includes the PWM comparator, OR gate, PWM latch,
and portions of the adaptive dead-time and control logic
block. During steady-state operation below the current
limit threshold, the PWM comparator output and oscillator
pulse train alternately reset and set the PWM latch. Once
the PWM latch is set, the low-side FET remains on for a
minimum duration set by the oscillator pulse duration.
During this period, the PWM ramp discharges rapidly to its
valley voltage. When the ramp begins to charge back up,
the low-side FET turns off and high-side FET turns on. As
the PWM ramp voltage exceeds the error amplifier output
voltage, the PWM comparator resets the latch, thus
turning off the high-side FET and turning on the low-side
FET. The low-side FET remains on until the next oscillator
pulse discharges the PWM ramp.
During transient conditions, the error amplifier output
could be below the PWM ramp valley voltage or above the
PWM peak voltage. If the error amplifier is high, the PWM
latch is never reset and the high-side FET remains on until
the oscillator pulse signals the control logic to turn the
high-side FET off and the low-side FET on. The device
operates at its maximum duty cycle until the output voltage
rises to the regulation set-point, setting VSENSE to
approximately the same voltage as Vref. If the error
amplifier output is low, the PWM latch is continually reset
and the high-side FET does not turn on. The low-side FET
remains on until the VSENSE voltage decreases to a
range that allows the PWM comparator to change states.
The TPS54311 through TPS54316 are capable of sinking
current continuously until the output reaches the
regulation set-point.
If the current limit comparator trips for longer than 100 ns,
the PWM latch resets before the PWM ramp exceeds the
error amplifier output. The high-side FET turns off and
low-side FET turns on to decrease the energy in the output
inductor and consequently the output current. This
process is repeated each cycle in which the current limit
comparator is tripped.
Dead-Time Control and MOSFET Drivers
Adaptive dead-time control prevents shoot-through
current from flowing in both N-channel power MOSFETs
during the switching transitions by actively controlling the
turn-on times of the MOSFET drivers. The high-side driver
does not turn on until the gate drive voltage to the low-side
FET is below 2 V. The low-side driver does not turn on until
the voltage at the gate of the high-side MOSFETs is below
2 V. The high-side and low-side drivers are designed with
300-mA source and sink capability to quickly drive the
power MOSFETs gates. The low-side driver is supplied
from VIN, while the high-side drive is supplied from the
BOOT pin. A bootstrap circuit uses an external BOOT
capacitor and an internal 2.5-
bootstrap switch
connected between the VIN and BOOT pins. The
integrated bootstrap switch improves drive efficiency and
reduces external component count.
Overcurrent Protection
The cycle by cycle current limiting is achieved by sensing
the current flowing through the high-side MOSFET and
differential amplifier and comparing it to the preset
overcurrent threshold. The high-side MOSFET is turned
off within 200 ns of reaching the current limit threshold. A
100-ns leading edge blanking circuit prevents false
tripping of the current limit. Current limit detection occurs
only when current flows from VIN to PH when sourcing
current to the output filter. Load protection during current
sink operation is provided by thermal shutdown.
Thermal Shutdown
The device uses the thermal shutdown to turn off the power
MOSFETs and disable the controller if the junction
temperature exceeds 150
°C. The device is released from
shutdown when the junction temperature decreases to
10
°C below the thermal shutdown trip point and starts up
under control of the slow-start circuit. Thermal shutdown
provides protection when an overload condition is
sustained for several milliseconds. With a persistent fault
相关PDF资料 |
PDF描述 |
|---|---|
| TPS54315QPWPRQ1 | 7.5 A SWITCHING REGULATOR, 762 kHz SWITCHING FREQ-MAX, PDSO20 |
| TPS54313QPWPRQ1 | 7.5 A SWITCHING REGULATOR, 762 kHz SWITCHING FREQ-MAX, PDSO20 |
| TPS54311QPWPRQ1 | 7.5 A SWITCHING REGULATOR, 762 kHz SWITCHING FREQ-MAX, PDSO20 |
| TPS60130PWPRG4 | 0.3 A SWITCHED CAPACITOR REGULATOR, 450 kHz SWITCHING FREQ-MAX, PDSO20 |
| TPS60132PWP | 0.15 A SWITCHED CAPACITOR REGULATOR, 450 kHz SWITCHING FREQ-MAX, PDSO20 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPS54317 | 制造商:TI 制造商全称:Texas Instruments 功能描述:1.6 MHz, 3-V TO 6-V INPUT, 3-A SYNCHRONOUS STEP-DOWN SWIFT⑩ CONVERTER WITH DISABLED SINKING DURING START-UP |
| TPS54317EVM-159 | 功能描述:电源管理IC开发工具 3-6Vin Step Down Conv RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| TPS54317RHF | 制造商:TI 制造商全称:Texas Instruments 功能描述:1.6 MHz, 3-V TO 6-V INPUT, 3-A SYNCHRONOUS STEP-DOWN SWIFT CONVERTER |
| TPS54317RHFR | 功能描述:直流/直流开关调节器 1.6MHz 3-6Vin Sync Step Dwn Converter RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| TPS54317RHFRG4 | 功能描述:直流/直流开关调节器 1.6MHz 3-6Vin Sync Step Dwn Converter RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
发布紧急采购，3分钟左右您将得到回复。