- 您现在的位置：买卖IC网 > PDF目录69511 > TPS54326RGTR (TEXAS INSTRUMENTS INC) 5.5 A SWITCHING REGULATOR, 700 kHz SWITCHING FREQ-MAX, PQCC16 PDF资料下载
参数资料
| 型号： | TPS54326RGTR |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 稳压器 |
| 英文描述： | 5.5 A SWITCHING REGULATOR, 700 kHz SWITCHING FREQ-MAX, PQCC16 |
| 封装： | GREEN, PLASTIC, QFN-16 |
| 文件页数： | 7/26页 |
| 文件大小： | 911K |
| 代理商： | TPS54326RGTR |
VOUT
VFB
VREG5
SS
GND
PG
EN
VCC
VIN
VBST
SW2
SW1
PGND1
PGND2
EXPOSED
POWERPAD
AREA
BOOST
CAPACITOR
VCC
INPUT
BYPASS
CAPACITOR
VOUT
VIA toGroundPlane
OUTPUT
INDUCTOR
OUTPUT
FILTER
CAPACITOR
SLOW
START
CAP
ANALOG
GROUND
TRACE
VIN
INPUT
BYPASS
CAPACITOR
VIN
FEEDBACK
RESISTORS
EtchonBottomLayer
orUnderComponent
ToEnable
Control
VCC
POWERGROUND
BIAS
CAP
Additional
Thermal
Vias
Additional
Thermal
Vias
Connectionto
POWERGROUND
oninternalor
bottomlayer
SLVSA13D
– OCTOBER 2009 – REVISED FEBRUARY 2011
LAYOUT CONSIDERATIONS
The following layout guidelines are provided using the PWP 14 pin package as an example. The general
guidelines and routing are also applicable to the QFN 16 pin package. Allowance should be made for the
differences in the package pin configurations.
1. Keep the input switching current loop as small as possible.
2. Keep the SW node as physically small and short as possible to minimize parasitic capacitance and
inductance and to minimize radiated emissions. Kelvin connections should be brought from the output to the
feedback pin of the device.
3. Keep analog and non-switching components away from switching components.
4. Make a single point connection from the signal ground to power ground.
5. Do not allow switching current to flow under the device.
6. Keep the pattern lines for VIN and PGND broad.
7. Exposed pad of device must be connected to PGND with solder.
8. VREG5 capacitor should be placed near the device, and connected PGND.
9. Output capacitor should be connected to a broad pattern of the PGND.
10. Voltage feedback loop should be as short as possible, and preferably with ground shield.
11. Lower resistor of the voltage divider which is connected to the VFB pin should be tied to SGND.
12. Providing sufficient via is preferable for VIN, SW and PGND connection.
13. PCB pattern for VIN, SW, and PGND should be as broad as possible.
14. If VIN and VCC is shorted, VIN and VCC patterns need to be connected with broad pattern lines.
15. VIN Capacitor should be placed as near as possible to the device.
Figure 14. TPS54326 Layout
2009–2011, Texas Instruments Incorporated
15
Product Folder Link(s) :TPS54326
相关PDF资料 |
PDF描述 |
|---|---|
| TPS54326PWPR | 5.5 A SWITCHING REGULATOR, 700 kHz SWITCHING FREQ-MAX, PDSO14 |
| TPS54331QDRQ1 | 2 A SWITCHING REGULATOR, 684 kHz SWITCHING FREQ-MAX, PDSO8 |
| TPS54332DDAR | SWITCHING REGULATOR, 1200 kHz SWITCHING FREQ-MAX, PDSO8 |
| TPS54350PWPR | 6.5 A SWITCHING REGULATOR, 700 kHz SWITCHING FREQ-MAX, PDSO16 |
| TPS54350PWP | 6.5 A SWITCHING REGULATOR, 700 kHz SWITCHING FREQ-MAX, PDSO16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPS54326RGTT | 功能描述:直流/直流开关转换器 4.5-18V Inp,3A Sync Step-Down SWIFT RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| TPS54327 | 制造商:TI 制造商全称:Texas Instruments 功能描述:3-A OUTPUT SINGLE SYNCHRONOUS STEP DOWN SWITCHER WITH INTEGRATED FET (SWIFTTM ) |
| TPS54327DDA | 功能描述:直流/直流开关转换器 4.5-18Vin,3A Sync Step-Down Cnvrtr RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| TPS54327DDAR | 功能描述:直流/直流开关转换器 4.5-18Vin,3A Sync Step-Down Cnvrtr RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| TPS54327DRCR | 制造商:Texas Instruments 功能描述:IC REG BUCK SYNC ADJ 3A 10SON 制造商:Texas Instruments 功能描述:3A Single Sync DC/DC converter |
发布紧急采购，3分钟左右您将得到回复。