- 您现在的位置：买卖IC网 > PDF目录225340 > TPS54429ERSAT (TEXAS INSTRUMENTS INC) 0.01 A SWITCHING REGULATOR, PQCC16 PDF资料下载
参数资料
| 型号： | TPS54429ERSAT |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 稳压器 |
| 英文描述： | 0.01 A SWITCHING REGULATOR, PQCC16 |
| 封装： | PLASTIC, QFN-16 |
| 文件页数： | 25/26页 |
| 文件大小： | 907K |
| 代理商： | TPS54429ERSAT |
SLVSAS0 –FEBRUARY 2011
The TPS54429E contains a unique circuit to prevent current from being pulled from the output during startup if
the output is pre-biased. When the soft-start commands a voltage higher than the pre-bias level (internal soft
start becomes greater than feedback voltage VFB), the controller slowly activates synchronous rectification by
starting the first low side FET gate driver pulses with a narrow on-time. It then increments that on-time on a
cycle-by-cycle basis until it coincides with the time dictated by (1-D), where D is the duty cycle of the converter.
This scheme prevents the initial sinking of the pre-bias output, and ensure that the out voltage (VO) starts and
ramps up smoothly into regulation and the control loop is given time to transition from pre-biased start-up to
normal mode operation.
Power Good
The TPS54429E has power-good open drain output. The power good function is activated after soft start has
finished. The power good function becomes active after 1.7 times soft-start time. When the output voltage is
within -10% of the target value, internal comparators detect power good state and the power good signal
becomes high. If the PG output is pulled up to VREG5, the resister value, which is connected between PG and
VREG5, must be in the range of 20k ohm to 150k ohm. If the feedback voltage goes under 15% of the target
value, the power good signal becomes low after a 5 μs internal delay.
VREG5
VREG5 is an internally generated voltage source used by the TPS54429E. It is derived directly from the input
voltage and is nominally regulated to 5.5 V when the input voltage is above 5.6 V. The output of the VREG5
regulator is the input to the internal UVLO function. VREG5 must be above the UVLO wake up threshold voltage
(3.8 V typical) for the TPS54429E to function. Connect a 1.0 F capacitor between pin 3 of the TPS54429E and
power ground for proper regulation of the VREG5 output. The VREG5 output voltage is available for external use
and can typically source up to 70 mA. The VREG5 output is disabled when the TPS54429E EN pin is open or
pulled low.
Output Discharge Control
TPS54429E discharges the output when EN is low, or the controller is turned off by the protection functions
(OVP, UVP, UVLO and thermal shutdown). The output is discharged by an internal 50- MOSFET which is
connected from VO to PGND. The internal low-side MOSFET is not turned on during the output discharge
operation to avoid the possibility of causing negative voltage at the output.
Current Protection
The output overcurrent protection (OCP) is implemented using a cycle-by-cycle valley detect control circuit. The
switch current is monitored by measuring the low-side FET switch voltage between the SW pin and GND. This
voltage is proportional to the switch current. To improve accuracy, the voltage sensing is temperature
compensated.
During the on-time of the high-side FET switch, the switch current increases at a linear rate determined by VIN,
VOUT, the on-time, and the output inductor value. During the on-time of the low-side FET switch, this current
decreases linearly. The average value of the switch current is the load current IOUT. If the measured voltage is
above the voltage proportional to the current limit, the device constantly monitors the low-side FET switch
voltage, which is proportional to the switch current, during the low-side on-time. The converter maintains the
low-side switch on until the measured voltage is below the voltage corresponding to the current limit at which
time the switching cycle is terminated and a new switching cycle begins. In subsequent switching cycles, the
on-time is set to a fixed value and the current is monitored in the same manner.
There are some important considerations for this type of overcurrent protection. The load current one half of the
peak-to-peak inductor current higher than the overcurrent threshold. Also when the current is being limited, the
output voltage tends to fall as the demanded load current may be higher than the current available from the
converter. This may cause the output under-voltage protection circuit to be activated. When the overcurrent
condition is removed, the output voltage will return to the regulated value. This protection is non-latching.
8
2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS54429E
相关PDF资料 |
PDF描述 |
|---|---|
| TPS60201DGSRG4 | SWITCHED CAPACITOR REGULATOR, 400 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS62000 | "Adjustable |
| TPS65166RHAR | SPECIALTY ANALOG CIRCUIT, PQCC40 |
| TPS65270RGET | DUAL SWITCHING CONTROLLER, 1400 kHz SWITCHING FREQ-MAX, PQCC24 |
| TPS65562RGTTG4 | 3 A BATTERY CHARGE CONTROLLER, PQCC16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPS54429EVM-608 | 功能描述:电源管理IC开发工具 TPS54429 Eval Mod RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| TPS54429PWP | 功能描述:直流/直流开关调节器 7V-18Vin,4.5A Sync Step-Down DCAP2 Mode RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| TPS54429PWPR | 功能描述:直流/直流开关调节器 7V-18Vin,4.5A Sync Step-Down DCAP2 Mode RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| TPS54478 | 制造商:TI 制造商全称:Texas Instruments 功能描述:2.95-V to 6-V Input, 4-A Output, 2-MHz, Synchronous Step-Down |
| TPS54478EVM-037 | 功能描述:电源管理IC开发工具 TPS54478 Eval Mod RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
发布紧急采购，3分钟左右您将得到回复。