- 您现在的位置：买卖IC网 > PDF目录150819 > TPS5633CPWPR (TEXAS INSTRUMENTS INC) SWITCHING CONTROLLER, PDSO28 PDF资料下载
参数资料
| 型号： | TPS5633CPWPR |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING CONTROLLER, PDSO28 |
| 封装： | PLASTIC, TSSOP-28 |
| 文件页数： | 16/25页 |
| 文件大小： | 387K |
| 代理商： | TPS5633CPWPR |
TPS5615, TPS5618, TPS5625, TPS5633
SYNCHRONOUS-BUCK HYSTERETIC REGULATOR CONTROLLER
SLVS177A – SEPTEMBER 1998 – REVISED NOVEMBER 1998
23
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
layout guidelines
Good power supply results will only occur when care is given to proper design and layout. Layout will affect noise
pickup and generation and can cause a good design to perform with less than expected results. With a range
of currents from milliamps to tens or even hundreds of amps, good power supply layout is much more difficult
than most general PCB design. The general design should proceed from the switching node to the output, then
back to the driver section and, finally, place the low-level components. Below are several specific points to
consider before layout of a TPS56xx design begins.
1.
All sensitive analog components should be referenced to ANAGND. These include components connected
to SLOWST, IOUT, OCP, VSENSE, VREFB, VHYST, BIAS, and LOHIB.
2.
Analog ground and drive ground should be isolated as much as possible. Ideally, analog ground will connect
to the ground side of the bulk storage capacitors, on VO, and drive ground will connect to the main ground
plane close to the source of the low-side FET.
3.
Connections from the drivers to the gate of the power FETs should be as short and wide as possible to
reduce stray inductance. This becomes more critical if external gate resistors are not being used.
4.
The bypass capacitor for the DRV regulator should be placed close to the TPS56xx and be connected to
DRVGND.
5.
The bypass capacitor for VCC should be placed close to the TPS56xx and be connected to DRVGND.
6.
When configuring the high-side driver as a floating driver, the connection from BOOTLO to the power FETs
should be as short and as wide as possible. The other pins that also connect to the power FETs, LOHIB
and LOSENSE, should have a separate connection to the FETs, since BOOTLO will have large peak
currents flowing through it.
7.
When configuring the high-side driver as a floating driver, the bootstrap capacitor (connected from BOOT
to BOOTLO) should be placed close to the TPS56xx.
8.
When configuring the high-side driver as a ground referenced driver, BOOTLO should be connected to
DRVGND.
9.
The bulk storage capacitors across VI should be placed close to the power FETs. High-frequency bypass
capacitors should be placed in parallel with the bulk capacitors and connected close to the drain of the
high-side FET and close to the source of the low-side FET.
10. High-frequency bypass capacitors should be placed across the bulk storage capacitors on VO.
11. HISENSE and LOSENSE should be connected very close to the drain and source, respectively, of the
high-side FET. HISENSE and LOSENSE should be routed very close to each other to minimize
differential-mode noise coupling to these traces.
相关PDF资料 |
PDF描述 |
|---|---|
| TL7709ACD | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| TL1431CD | 1-OUTPUT THREE TERM VOLTAGE REFERENCE, 2.5 V, PDSO8 |
| TC1272-15ENB713 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 |
| TC1276-15ENB713 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 |
| TL431AIDM | 1-OUTPUT THREE TERM VOLTAGE REFERENCE, PDSO8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPS5633EVM-104 | 功能描述:EVAL MOD FOR TPS5633 RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| TPS5633EVM-111 | 功能描述:HIGH-PERFORMANCE SYNCHRONOUS BUC RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| TPS5633PWP | 功能描述:DC/DC 开关控制器 High Crnt Synch Buck Cntrlr RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| TPS5633PWPG4 | 功能描述:DC/DC 开关控制器 High Crnt Synch Buck Cntrlr RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| TPS5633PWPR | 功能描述:DC/DC 开关控制器 High Crnt Synch Buck Cntrlr RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。