- 您现在的位置：买卖IC网 > PDF目录69514 > TPS61006DGSRG4 (TEXAS INSTRUMENTS INC) 1.3 A SWITCHING REGULATOR, 840 kHz SWITCHING FREQ-MAX, PDSO10 PDF资料下载
参数资料
| 型号： | TPS61006DGSRG4 |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 稳压器 |
| 英文描述： | 1.3 A SWITCHING REGULATOR, 840 kHz SWITCHING FREQ-MAX, PDSO10 |
| 封装： | GREEN, PLASTIC, MSOP-10 |
| 文件页数： | 7/25页 |
| 文件大小： | 456K |
| 代理商： | TPS61006DGSRG4 |
TPS61000, TPS61001, TPS61002, TPS61003, TPS61004, TPS61005, TPS61006, TPS61007
SINGLE- AND DUAL-CELL BOOST CONVERTER WITH START-UP INTO FULL LOAD
SLVS279C – MARCH 2000 – REVISED APRIL 2003
15
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
programming the low battery comparator threshold voltage
The current through the resistive divider should be about 100 times greater than the current into the LBI pin.
The typical current into the LBI pin is 0.01
A. The voltage across R2 is equal to the reference voltage that is
generated on-chip, which has a value of 500 mV
±15 mV. The recommended value for R2 is therefore in the
range of 500 k
. From that, the value of resistor R1, depending on the desired minimum battery voltage (VBAT),
can be calculated using the following equation:
R1
+ R2
V
TRIP
V
REF
* 1 + 500 k
V
BAT
0.5 V
* 1
(2)
For example, if the low-battery detection circuit should flag an error condition on the LBO output pin at a battery
voltage of 1.0 V, a resistor in the range of 500 k
should be chosen for R1.
The output of the low battery comparator is a simple open-drain output that goes active low if the battery voltage
drops below the programmed threshold voltage on LBI. The output requires a pullup resistor with a
recommended value of 1M
, and should only be pulled up to the VOUT. If not used, the LBO pin can be left
floating.
inductor selection
The output filter of inductive switching regulators is a low pass filter of second order. It consists of an inductor and
a capacitor, often referred to as storage inductor and output capacitor.
To select an inductor, keep the possible peak inductor current below the current limit threshold of the power
switch in your chosen configuration. For example, the current limit threshold of the TPS61006’s switch is
1100 mA at an output voltage of 3.3 V. The highest peak current through the inductor and the switch depends on
the output load, the input (VBAT), and the output voltage (VOUT). Estimation of the maximum average inductor
current can be done using the following equation:
I
L +
I
OUT
x
V
OUT
V
BAT
x0.8
(3)
For example, for an output current of 100 mA at 3.3 V, at least 515-mA current flows through the inductor at a
minimum input voltage of 0.8 V.
The second parameter for choosing the inductor is the desired current ripple in the inductor. Normally it is advis-
able to work with a ripple of less than 20% of the average inductor current. A smaller ripple reduces the magnetic
hysteresis losses in the inductor as well as output voltage ripple and EMI. But in the same way, the regulation
time at load change rises. In addition, a larger inductor increases the total system cost.
相关PDF资料 |
PDF描述 |
|---|---|
| TPS61004DGSR | 1.3 A SWITCHING REGULATOR, 840 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS61007DGS | 1.3 A SWITCHING REGULATOR, 840 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS61006DGSR | 1.3 A SWITCHING REGULATOR, 840 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS61005DGSR | 1.3 A SWITCHING REGULATOR, 840 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS61001DGS | 1.3 A SWITCHING REGULATOR, 840 kHz SWITCHING FREQ-MAX, PDSO10 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPS61006DGST | 制造商:TI 制造商全称:Texas Instruments 功能描述:SINGLE- AND DUAL-CELL BOOST CONVERTER WITH START-UP INTO FULL LOAD |
| TPS61006DSGR | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
| TPS61006EVM-156 | 功能描述:电源管理IC开发工具 Low Input Vltg Boost Conv RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| TPS61007 | 制造商:TI 制造商全称:Texas Instruments 功能描述:SINGLE- AND DUAL-CELL BOOST CONVERTER WITH START-UP INTO FULL LOAD |
| TPS61007DGS | 功能描述:直流/直流开关调节器 Adj. 100mA Boost RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
发布紧急采购，3分钟左右您将得到回复。