- 您现在的位置：买卖IC网 > PDF目录69514 > TPS61013DGS (TEXAS INSTRUMENTS INC) 1.3 A SWITCHING REGULATOR, 780 kHz SWITCHING FREQ-MAX, PDSO10 PDF资料下载
参数资料
| 型号： | TPS61013DGS |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 稳压器 |
| 英文描述： | 1.3 A SWITCHING REGULATOR, 780 kHz SWITCHING FREQ-MAX, PDSO10 |
| 封装： | GREEN, PLASTIC, MSOP-10 |
| 文件页数： | 8/33页 |
| 文件大小： | 868K |
| 代理商： | TPS61013DGS |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
www.ti.com
R1 + R2
V
BAT
V
REF
–1
+ 500 kW
V
BAT
500 mV
–1
(2)
inductor selection
I
L + IOUT
V
O
V
BAT
0.8
(3)
L +
V
BAT
V
OUT * VBAT
DIL
V
OUT
(4)
TPS61010, TPS61011
TPS61012, TPS61013
TPS61014, TPS61015, TPS61016
SLVS314D – SEPTEMBER 2000 – REVISED JUNE 2005
For example, if the low-battery detection circuit should flag an error condition on the LBO output pin at a battery
voltage of 1 V, a resistor in the range of 500 k
should be chosen for R1. The output of the low battery
comparator is a simple open-drain output that goes active low if the battery voltage drops below the programmed
threshold voltage on LBI. The output requires a pullup resistor with a recommended value of 1 M
, and should
only be pulled up to the VO. If not used, the LBO pin can be left floating or tied to GND.
A boost converter normally requires two main passive components for storing energy during the conversion. A
boost inductor is required and a storage capacitor at the output. To select the boost inductor, it is recommended
to keep the possible peak inductor current below the current limit threshold of the power switch in the chosen
configuration. For example, the current limit threshold of the TPS61010's switch is 1100 mA at an output voltage
of 3.3 V. The highest peak current through the inductor and the switch depends on the output load, the input
(VBAT), and the output voltage (VO). Estimation of the maximum average inductor current can be done using
Equation 3.
For example, for an output current of 100 mA at 3.3 V, at least 515-mA of current flows through the inductor at a
minimum input voltage of 0.8 V.
The second parameter for choosing the inductor is the desired current ripple in the inductor. Normally, it is
advisable to work with a ripple of less than 20% of the average inductor current. A smaller ripple reduces the
magnetic hysteresis losses in the inductor, as well as output voltage ripple and EMI. But in the same way,
regulation time at load changes rises. In addition, a larger inductor increases the total system costs.
With those parameters, it is possible to calculate the value for the inductor by using Equation 4.
Parameter 7 is the switching frequency and
I
L is the ripple current in the inductor, i.e., 20% × IL.
In this example, the desired inductor has the value of 12 H. With this calculated value and the calculated
currents, it is possible to choose a suitable inductor. Care must be taken that load transients and losses in the
circuit can lead to higher currents as estimated in Equation 3. Also, the losses in the inductor caused by
magnetic hysteresis losses and copper losses are a major parameter for total circuit efficiency.
The following inductor series from different suppliers were tested. All work with the TPS6101x converter within
their specified parameters:
Table 1. Recommended Inductors
VENDOR
RECOMMENDED INDUCTOR SERIES
Sumida
Sumida CDR74B
Sumida CDRH74
Sumida CDRH5D18
Sumida CDRH6D38
Coilcraft
Coilcraft DO 1608C
Coilcraft DS 1608C
Coilcraft DS 3316
Coilcraft DT D03308P
Coiltronics
Coiltronics UP1B
Coiltronics UP2B
16
相关PDF资料 |
PDF描述 |
|---|---|
| TPS61010DGSG4 | 1.3 A SWITCHING REGULATOR, 780 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS61014DGSG4 | 1.3 A SWITCHING REGULATOR, 780 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS61015DGS | 1.3 A SWITCHING REGULATOR, 780 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS61013DGSR | 1.3 A SWITCHING REGULATOR, 780 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS61016DGSG4 | 1.3 A SWITCHING REGULATOR, 780 kHz SWITCHING FREQ-MAX, PDSO10 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPS61013DGSG4 | 功能描述:直流/直流开关调节器 Lo-In Voltage Sync Boost Converter RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| TPS61013DGSR | 功能描述:开关变换器、稳压器与控制器 Lo-In Voltage Sync Boost Converter RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| TPS61013DGSRG4 | 功能描述:开关变换器、稳压器与控制器 Lo-In Voltage Sync Boost Converter RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| TPS61013EVM-157 | 功能描述:电源管理IC开发工具 Fixed 2.5-V High-Eff Boost Conv RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| TPS61014 | 制造商:TI 制造商全称:Texas Instruments 功能描述:HIGH-EFFICIENCY, 1-CELL AND 2-CELL BOOST CONVERTERS |
发布紧急采购，3分钟左右您将得到回复。