- 您现在的位置：买卖IC网 > PDF目录69515 > TPS61040DBV (TEXAS INSTRUMENTS INC) 0.45 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO5 PDF资料下载
参数资料
| 型号： | TPS61040DBV |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 稳压器 |
| 英文描述： | 0.45 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO5 |
| 封装： | GREEN, PLASTIC, SOT-23, 5 PIN |
| 文件页数： | 2/27页 |
| 文件大小： | 779K |
| 代理商： | TPS61040DBV |
第1页当前第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页
fSmax +
V
IN(min)
(V
OUT *
V
IN)
I
P
L
V
OUT
fS I
load +
2
I
load
(V
OUT *
V
IN )
Vd)
I 2
P
L
I
load max +
h
I 2
P
L
fSmax
2
(V
OUT *
V
IN)
SLVS413F – OCTOBER 2002 – REVISED DECEMBER 2010
www.ti.com
APPLICATION INFORMATION
INDUCTOR SELECTION, MAXIMUM LOAD CURRENT
Because the PFM peak current control scheme is inherently stable, the inductor value does not affect the stability
of the regulator. The selection of the inductor together with the nominal load current, input and output voltage of
the application determines the switching frequency of the converter. Depending on the application, inductor
values between 2.2 mH and 47 mH are recommended. The maximum inductor value is determined by the
maximum on time of the switch, typically 6 ms. The peak current limit of 400 mA/250 mA (typically) should be
reached within this 6-ms period for proper operation.
The inductor value determines the maximum switching frequency of the converter. Therefore, select the inductor
value that ensures the maximum switching frequency at the converter maximum load current is not exceeded.
The maximum switching frequency is calculated by the following formula:
Where:
L = Selected inductor value
VIN(min) = The highest switching frequency occurs at the minimum input voltage
(2)
If the selected inductor value does not exceed the maximum switching frequency of the converter, the next step
is to calculate the switching frequency at the nominal load current using the following formula:
Where:
L = Selected inductor value
Iload = Nominal load current
Vd = Rectifier diode forward voltage (typically 0.3V)
(3)
A smaller inductor value gives a higher converter switching frequency, but lowers the efficiency.
The inductor value has less effect on the maximum available load current and is only of secondary order. The
best way to calculate the maximum available load current under certain operating conditions is to estimate the
expected converter efficiency at the maximum load current. This number can be taken out of the efficiency
graphs shown in Figure 1 through Figure 4. The maximum load current can then be estimated as follows:
Where:
L = Selected inductor value
fSmax = Maximum switching frequency as calculated previously
h = Expected converter efficiency. Typically 70% to 85%
(4)
10
Copyright 2002–2010, Texas Instruments Incorporated
相关PDF资料 |
PDF描述 |
|---|---|
| TPS61040DRVTG4 | 0.45 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO6 |
| TPS61041DRVR | 0.285 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO6 |
| TPS61059DRCTG4 | 1.8 A SWITCHING REGULATOR, 750 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS61070TDDCRQ1 | SWITCHING REGULATOR, PDSO6 |
| TPS61073DDCRG4 | 0.7 A BATTERY CHARGE CONTROLLER, 1440 kHz SWITCHING FREQ-MAX, PDSO6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPS61040DBVR | 功能描述:LED照明驱动器 28-V 400-mA Switch Boost Converter RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| TPS61040DBVR | 制造商:Texas Instruments 功能描述:Power Supply IC |
| TPS61040DBVRG4 | 功能描述:LED照明驱动器 28-V 400-mA Switch Boost Converter RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| TPS61040DBVT | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
| TPS61040DDCR | 功能描述:LED照明驱动器 28V,400mA Switch Boost Converter RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
发布紧急采购，3分钟左右您将得到回复。