- 您现在的位置：买卖IC网 > PDF目录69516 > TPS61240YFFR (TEXAS INSTRUMENTS INC) 0.45 A SWITCHING REGULATOR, 3500 kHz SWITCHING FREQ-MAX, BGA6 PDF资料下载
参数资料
| 型号： | TPS61240YFFR |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 稳压器 |
| 英文描述： | 0.45 A SWITCHING REGULATOR, 3500 kHz SWITCHING FREQ-MAX, BGA6 |
| 封装： | 0.40 MM PITCH, GREEN, DSBGA-6 |
| 文件页数： | 7/26页 |
| 文件大小： | 755K |
| 代理商： | TPS61240YFFR |
(
)
OU T
IN
mi n
OU T
I
V
C
=
f
V
-
D
www.ti.com
SLVS806A – APRIL 2009 – REVISED MAY 2009
INPUT CAPACITOR
At least 2.2mF input capacitor is recommended to improve transient behavior of the regulator and EMI behavior
of the total power supply circuit. It is recommended to place a ceramic capacitor as close as possible to the VIN
and GND pins
OUTPUT CAPACITOR
For the output capacitor, it is recommended to use small ceramic capacitors placed as close as possible to the
VOUT and GND pins of the IC. If, for any reason, the application requires the use of large capacitors which can
not be placed close to the IC, using a smaller ceramic capacitor in parallel to the large one is recommended.
This small capacitor should be placed as close as possible to the VOUT and GND pins of the IC. To get an
estimate of the recommended minimum output capacitance, Equation 5 can be used.
(5)
Parameter f is the switching frequency and
ΔV is the maximum allowed ripple.
With a chosen ripple voltage of 10 mV, a minimum effective capacitance of 2.7 mF is needed. The total ripple is
larger due to the ESR of the output capacitor. This additional component of the ripple can be calculated using
ΔVESR = IOUT x RESR
A capacitor with a value in the range of the calculated minimum should be used. This is required to maintain
control loop stability. There are no additional requirements regarding minimum ESR. There is no upper limit for
the output capacitance value. Larger capacitors cause lower output voltage ripple as well as lower output voltage
drop during load transients.
Note that ceramic capacitors have a DC Bias effect, which will have a strong influence on the final effective
capacitance needed. Therefore the right capacitor value has to be chosen carefully. Package size and voltage
rating in combination with material are responsible for differences between the rated capacitor value and the
effective capacitance.
CHECKING LOOP STABILITY
The first step of circuit and stability evaluation is to look from a steady-state perspective at the following signals:
Switching node, SW
Inductor current, IL
Output ripple voltage, VO(AC)
These are the basic signals that need to be measured when evaluating a switching converter. When the
switching waveform shows large duty cycle jitter or the output voltage or inductor current shows oscillations, the
regulation loop may be unstable. This is often a result of board layout and/or L-C combination.
As a next step in the evaluation of the regulation loop, the load transient response is tested. The time between
the application of the load transient and the turn on of the P-channel MOSFET, the output capacitor must supply
all of the current required by the load. VO immediately shifts by an amount equal to ΔI(LOAD) × ESR, where ESR is
the effective series resistance of CO. ΔI(LOAD) begins to charge or discharge CO generating a feedback error
signal used by the regulator to return VO to its steady-state value. The results are most easily interpreted when
the device operates in PWM mode. During this recovery time, VO can be monitored for settling time, overshoot or
ringing that helps judge the converter’s stability. Without any ringing, the loop has usually more than 45° of phase
margin. Because the damping factor of the circuitry is directly related to several resistive parameters (e.g.,
MOSFET rDS(on)) that are temperature dependant, the loop stability analysis has to be done over the input voltage
range, load current range, and temperature range.
Copyright 2009, Texas Instruments Incorporated
15
Product Folder Link(s) :TPS61240, TPS61241
相关PDF资料 |
PDF描述 |
|---|---|
| TPS61240YFFT | 0.45 A SWITCHING REGULATOR, 3500 kHz SWITCHING FREQ-MAX, BGA6 |
| TPS61260DRVR | 0.1 A SWITCHING CONTROLLER, 2500 kHz SWITCHING FREQ-MAX, PDSO6 |
| TPS61261DRVT | 0.1 A SWITCHING CONTROLLER, 2500 kHz SWITCHING FREQ-MAX, PDSO6 |
| TPS61260DRVT | 0.1 A SWITCHING CONTROLLER, 2500 kHz SWITCHING FREQ-MAX, PDSO6 |
| TPS62008QDGSRQ1 | 1.6 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO10 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPS61240YFFT | 功能描述:直流/直流开关调节器 5V, 400mA, 4MHz Step Up DC/DC Converter RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| TPS61240YFFT | 制造商:Texas Instruments 功能描述:DC/DC Converter IC |
| TPS61241 | 制造商:TI 制造商全称:Texas Instruments 功能描述:3.5-MHz High Efficiency Step-Up Converter |
| TPS61241YFF | 制造商:TI 制造商全称:Texas Instruments 功能描述:3.5-MHz High Efficiency Step-Up Converter |
| TPS61241YFFR | 功能描述:直流/直流开关调节器 5V 500mA 4MHz Step- Up DC/DC Cnvrtr RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
发布紧急采购，3分钟左右您将得到回复。