- 您现在的位置：买卖IC网 > PDF目录69516 > TPS62044DRCR (TEXAS INSTRUMENTS INC) 2.2 A SWITCHING REGULATOR, 1500 kHz SWITCHING FREQ-MAX, PDSO10 PDF资料下载
参数资料
| 型号： | TPS62044DRCR |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 稳压器 |
| 英文描述： | 2.2 A SWITCHING REGULATOR, 1500 kHz SWITCHING FREQ-MAX, PDSO10 |
| 封装： | 3 X 3 MM, GREEN, PLASTIC, SON-10 |
| 文件页数： | 8/30页 |
| 文件大小： | 790K |
| 代理商： | TPS62044DRCR |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
TPS62040
TPS62042, TPS62043
TPS62044, TPS62046
SLVS463B JUNE 2003 REVISED OCTOBER 2005
www.ti.com
16
Layout Considerations
For all switching power supplies, the layout is an important step in the design especially at high peak currents and
switching frequencies. If the layout is not carefully done, the regulator might show stability problems as well as EMI
problems. Therefore, use wide and short traces for the main current paths as indicated in bold in Figure 16. These
traces should be routed first. The input capacitor should be placed as close as possible to the IC pins as well as the
inductor and output capacitor. The feedback resistor network should be routed away from the inductor and switch
node to minimize noise and magnetic interference. To further minimize noise from coupling into the feedback network
and feedback pin, the ground plane or ground traces should be used for shielding. A common ground plane or a star
ground as shown below should be used. This becomes very important especially at high switching frequencies of
1.25 MHz.
VIN
EN
MODE
SW
FB
PGND
SW
GND
2
3
1
49
10
5
7
8
6
TPS6204x
C3
22 F
VI
L1
10 H
C2
22 F
VO
The Switch Node Must Be
Kept as Small as Possible
Figure 16. Layout Diagram
THERMAL INFORMATION
One of the most influential components on the thermal performance of a package is board design. In order to take
full advantage of the heat dissipating abilities of the PowerPADt packages, a board should be used that acts similar
to a heat sink and allows for the use of the exposed (and solderable), deep downset pad. For further information
please refer to Texas Instruments application note (SLMA002) PowerPAD Thermally Enhanced Package.
The PowerPADt of the 10-pin MSOP package has an area of 1,52 mm × 1,79 mm (± 0,05 mm) and must be soldered
to the PCB to lower the thermal resistance. Thermal vias to the next layer further reduce the thermal resistance.
相关PDF资料 |
PDF描述 |
|---|---|
| TPS62042DGQ | 2.2 A SWITCHING REGULATOR, 1500 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS62046DGQRG4 | 2.2 A SWITCHING REGULATOR, 1500 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS62042DGQR | 2.2 A SWITCHING REGULATOR, 1500 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS62043DGQ | 2.2 A SWITCHING REGULATOR, 1500 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS62044DGQRG4 | 2.2 A SWITCHING REGULATOR, 1500 kHz SWITCHING FREQ-MAX, PDSO10 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPS62044DRCRG4 | 功能描述:直流/直流开关调节器 1.8V Out 1.2A Hi-Ef Step-Down Converter RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| TPS62046DGQ | 功能描述:直流/直流开关调节器 3.3V Out/1.2A Hi-Eff Step-Down Converter RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| TPS62046DGQG4 | 功能描述:直流/直流开关调节器 3.3V Out/1.2A Hi-Eff Step-Down Converter RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| TPS62046DGQR | 功能描述:直流/直流开关调节器 3.3V Out/1.2A Hi-Eff Step-Down Converter RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| TPS62046DGQR | 制造商:Texas Instruments 功能描述:DC/DC CONVERTER IC 制造商:Texas Instruments 功能描述:IC, STEP-DOWN CONVERTER, MSOP-10 |
发布紧急采购，3分钟左右您将得到回复。