- 您现在的位置：买卖IC网 > PDF目录136953 > TPS62202DBVR (TEXAS INSTRUMENTS INC) 0.67 A SWITCHING REGULATOR, 1500 kHz SWITCHING FREQ-MAX, PDSO5 PDF资料下载
参数资料
| 型号： | TPS62202DBVR |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 稳压器 |
| 英文描述： | 0.67 A SWITCHING REGULATOR, 1500 kHz SWITCHING FREQ-MAX, PDSO5 |
| 封装： | GREEN, PLASTIC, SOT-23, 5 PIN |
| 文件页数： | 4/22页 |
| 文件大小： | 461K |
| 代理商： | TPS62202DBVR |
www.ti.com
APPLICATION INFORMATION
ADJUSTABLE OUTPUT VOLTAGE VERSION
Vout + 0.5 V
1 )
R1
R2
C1 +
1
2
p
10 kHz
R1
C2 +
R1
R2
C1
VI
GND
EN
SW
FB
C3
4.7
F
L1
10
H
C4
10
F
TPS62200
VI
2.5 V 6 V
VO
1.8 V / 300 mA
R1
470k
R2
180k
C1
33 pF
C2
100 pF
INDUCTOR SELECTION
SLVS417E – MARCH 2002 – REVISED MAY 2006
When the adjustable output voltage version TPS62200 is used, the output voltage is set by the external resistor
divider. See Figure 16.
The output voltage is calculated as
R1 + R2
≤ 1 M and internal reference voltage V(ref)typ = 0.5 V
R1 + R2 should not be greater than 1 M
for reasons of stability. To keep the operating quiescent current to a
minimum, the feedback resistor divider should have high impedance with R1+R2
≤ 1 M. Because of the high
impedance and the low reference voltage of Vref = 0.5 V, the noise on the feedback pin (FB) needs to be
minimized. Using a capacitive divider C1 and C2 across the feedback resistors minimizes the noise at the
feedback without degrading the line or load transient performance.
C1 and C2 should be selected as
R1 = upper resistor of voltage divider
C1 = upper capacitor of voltage divider
For C1 a value should be chosen that comes closest to the calculated result.
R2 = lower resistor of voltage divider
C2 = lower capacitor of voltage divider
For C2 the selected capacitor value should always be selected larger than the calculated result. For example, in
Figure 16 for C2, 100 pF are selected for a calculated result of C2 = 86.17 pF.
If quiescent current is not a key design parameter, C1 and C2 can be omitted, and a low-impedance feedback
divider must be used with R1+R2 <100 k
. This design reduces the noise available on the feedback pin (FB) as
well, but increases the overall quiescent current during operation.
Figure 16. Typical Application Circuit for the Adjustable Output Voltage
The TPS6220x device is optimized to operate with a typical inductor value of 10 H.
For high efficiencies, the inductor should have a low dc resistance to minimize conduction losses. Although the
inductor core material has less effect on efficiency than its dc resistance, an appropriate inductor core material
must be used.
12
相关PDF资料 |
PDF描述 |
|---|---|
| TPS2111APW | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| TPS2060DGNR | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| TPS54331DDAR | 2 A SWITCHING REGULATOR, 684 kHz SWITCHING FREQ-MAX, PDSO8 |
| TC151A5313EOA713 | 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8 |
| TC151A4317EOA713 | 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPS62202DBVRG4 | 功能描述:直流/直流开关调节器 1.8V Out Hi-Eff Step-Down Converter RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| TPS62202DBVT | 功能描述:直流/直流开关调节器 1.8V Out Hi-Eff Step-Down Converter RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| TPS62202DBVT | 制造商:Texas Instruments 功能描述:DC/DC Converter IC |
| TPS62202DBVTG4 | 功能描述:直流/直流开关调节器 1.8V Out Hi-Eff Step-Down Converter RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| TPS62203DBVR | 功能描述:直流/直流开关调节器 3.3V Out Hi-Eff Step-Down Converter RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
发布紧急采购，3分钟左右您将得到回复。