参数资料
型号: TPS63012YFF
厂商: TEXAS INSTRUMENTS INC
元件分类: 稳压器
英文描述: 2.4 A SWITCHING REGULATOR, 2600 kHz SWITCHING FREQ-MAX, BGA20
封装: 2.14 X 1.93 MM, LEAD FREE, DSBGA-20
文件页数: 9/28页
文件大小: 662K
代理商: TPS63012YFF
DETAILED DESCRIPTION
CONTROLLER CIRCUIT
Synchronous Operation
Buck-Boost Operation
Power Save Mode
www.ti.com ........................................................................................................................................................ SLVS653A – JUNE 2008 – REVISED AUGUST 2009
The controlling circuit of the device is based on an average current mode topology. The average inductor current
is regulated by a fast current regulator loop which is controlled by a voltage control loop. The controller also uses
input and output voltage feedforward. Changes of input and output voltage are monitored and immediately can
change the duty cycle in the modulator to achieve a fast response to those errors. The voltage error amplifier
gets its feedback input from the FB pin. At adjustable output voltages a resistive voltage divider must be
connected to that pin. At fixed output voltages FB must be connected to the output voltage to directly sense the
voltage. Fixed output voltage versions use a trimmed internal resistive divider. The feedback voltage will be
compared with the internal reference voltage to generate a stable and accurate output voltage.
The controller circuit also senses the average input current as well as the peak input current. With this, maximum
input power can be controlled as well as the maximum peak current to achieve a safe and stable operation under
all possible conditions. To finally protect the device from overheating, an internal temperature sensor is
implemented.
The device uses 4 internal N-channel MOSFETs to maintain synchronous power conversion at all possible
operating conditions. This enables the device to keep high efficiency over a wide input voltage and output power
range.
To avoid ground shift problems due to the high currents in the switches, two separate ground pins GND and
PGND are used. The reference for all control functions is the GND pin. The power switches are connected to
PGND. Both grounds must be connected on the PCB at only one point ideally close to the GND pin. Due to the
4-switch topology, the load is always disconnected from the input during shutdown of the converter.
To be able to regulate the output voltage properly at all possible input voltage conditions, the device
automatically switches from step down operation to boost operation and back as required by the configuration. It
always uses one active switch, one rectifying switch, one switch permanently on, and one switch permanently off.
Therefore, it operates as a step down converter (buck) when the input voltage is higher than the output voltage,
and as a boost converter when the input voltage is lower than the output voltage. There is no mode of operation
in which all 4 switches are permanently switching. Controlling the switches this way allows the converter to
maintain high efficiency at the most important point of operation; when input voltage is close to the output
voltage. The RMS current through the switches and the inductor is kept at a minimum, to minimize switching and
conduction losses. Switching losses are also kept low by using only one active and one passive switch.
Regarding the remaining 2 switches, one is kept permanently on and the other is kept permanently off, thus
causing no switching losses.
The PS pin can be used to select different operation modes. To enable power save, PS must be set low. Power
save mode is used to improve efficiency at light load. If power save mode is enabled, the converter stops
operating if the average inductor current gets lower than about 300 mA and the output voltage is at or above its
nominal value. If the output voltage decreases below its nominal value, the device ramps up the output voltage
again by starting operation using a programmed average inductor current higher than required by the current
load condition. Operation can last for one or several pulses. The converter again stops operating once the
conditions for stopping operation are met again.
The power save mode can be disabled by programming high at PS. The PS input supports standard logic
threshold voltages. If the device is synchronized to an external clock connected to SYNC, power save mode is
disabled.
Copyright 2008–2009, Texas Instruments Incorporated
17
Product Folder Link(s): TPS63010 TPS63011 TPS63012
相关PDF资料
PDF描述
TPS63020DSJ 4.5 A SWITCHING REGULATOR, 2600 kHz SWITCHING FREQ-MAX, PDSO14
TPS63020DSJR 4.5 A SWITCHING REGULATOR, 2600 kHz SWITCHING FREQ-MAX, PDSO14
TPS63021DSJT 4.5 A SWITCHING REGULATOR, 2600 kHz SWITCHING FREQ-MAX, PDSO14
TPS63021DSJ 4.5 A SWITCHING REGULATOR, 2600 kHz SWITCHING FREQ-MAX, PDSO14
TPS63030DSK 1.1 A SWITCHING REGULATOR, 2600 kHz SWITCHING FREQ-MAX, PDSO10
相关代理商/技术参数
参数描述
TPS63012YFFR 功能描述:直流/直流开关调节器 Hi Eff Sgl Inductor Buck-Boost Cnvrtr RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5
TPS63012YFFT 功能描述:直流/直流开关调节器 Hi Eff Sgl Inductor Buck-Boost Cnvrtr RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5
TPS63012YFFT 制造商:Texas Instruments 功能描述:Power Supply IC
TPS63020DSJR 功能描述:直流/直流开关调节器 93% Eff Buck-Boost Converter RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5
TPS63020DSJT 功能描述:直流/直流开关调节器 93% Eff Buck-Boost Converter RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5