参数资料
型号: TPS65735RSNR
厂商: TEXAS INSTRUMENTS INC
元件分类: 模拟信号调理
英文描述: SPECIALTY ANALOG CIRCUIT, PQCC32
封装: GREEN, PLASTIC, QFN-32
文件页数: 11/32页
文件大小: 1324K
代理商: TPS65735RSNR
0
10
20
30
40
50
60
70
80
90
100
0.01
0.1
1
2
Output Current (mA)
Efficiency
(%)
VOUT = 16.0 V
VIN = 3.0 V
G000
0
10
20
30
40
50
60
70
80
90
100
0.01
0.1
1
2
Output Current (mA)
Efficiency
(%)
VOUT = 16.0 V
VIN = 3.7 V
G000
0
10
20
30
40
50
60
70
80
90
100
0.01
0.1
1
2
Output Current (mA)
Efficiency
(%)
VOUT = 16.0 V
VIN = 4.2 V
G000
0
10
20
30
40
50
60
70
80
90
100
0.01
0.1
1
2
Output Current (mA)
Efficiency
(%)
VOUT = 16.0 V
VIN = 5.5 V
G000
SLVSAI6
– JUNE 2011
2.9
Boost Converter Operation
The boost converter in this device is designed for the load of active shutter 3D glasses. This load is
typically a light load where the average current is 2 mA or lower and the peak current out of a battery is
limited in operation. This asynchronous boost converter operates with a minimum off time / maximum on
time for the integrated low side switch, these values are specified in the electrical characteristics table of
this datasheet.
The peak output voltage from the boost converter is adjustable and set by using an external resistor
divider connected between BST_OUT, the BST_FB pin, and ground. The peak output voltage is set by
choosing resistors for the feedback network such that the voltage on the BST_FB pin is VREF(BST) = 1.2 V.
See Section 3.3 for more information on calculating resistance values for this feedback network.
The efficiency curves for various input voltages over the typical 3D glasses load range (2 mA and lower)
are shown below. All curves are for a target VOUT of 16 V. For output voltages less than 16 V, a higher
efficiency at each operating input voltage should be expected. Note that efficiency is dependent upon the
external boost feedback network resistances, the inductor used, and the type of load connected.
Figure 2-6. Boost Efficiency vs. IOUT, VIN = 3.0 V,
Figure 2-7. Boost Efficiency vs. IOUT, VIN = 3.7 V,
VOUT = 16 V
Figure 2-8. Boost Efficiency vs. IOUT, VIN = 4.2 V,
Figure 2-9. Boost Efficiency vs. IOUT, VIN = 5.5 V,
VOUT = 16 V
2.9.1
Boost Thermal Shutdown
An internal thermal shutdown mode is implemented in the boost converter that shuts down the device if
the typical junction temperature of 105
°C is exceeded. If the device is in thermal shutdown mode, the
main switch of the boost is open and the device enters the "SLEEP / POWER OFF" state.
Copyright
2011, Texas Instruments Incorporated
POWER MANAGEMENT CORE
19
Product Folder Link(s): TPS65735
相关PDF资料
PDF描述
TPS70702PWP DUAL-OUTPUT LOW-DROPOUT VOLTAGE REGULATORS WITH POWER UP SEQUENCING FOR SPLIT VOLTAGE DSP SYSTEMS
TPS70745PWP DUAL-OUTPUT LOW-DROPOUT VOLTAGE REGULATORS WITH POWER UP SEQUENCING FOR SPLIT VOLTAGE DSP SYSTEMS
TPS70751PWP DUAL-OUTPUT LOW-DROPOUT VOLTAGE REGULATORS WITH POWER UP SEQUENCING FOR SPLIT VOLTAGE DSP SYSTEMS
TPS70758PWPRG4 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO20
TPS70802PWP DUAL-OUTPUT LOW-DROPOUT VOLTAGE REGULATORS WITH INTEGRATED SVS FOR SPLIT VOLTAGE SYSTEMS
相关代理商/技术参数
参数描述
TPS65800EVM 功能描述:电源管理IC开发工具 TPS65800 Eval Mod RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
TPS65800RTQR 功能描述:电池管理 1-Cell L-Ion Battery & Pwr Mngmnt IC RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel
TPS65800RTQRG4 功能描述:电池管理 1-Cell L-Ion Battery & Pwr Mngmnt IC RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel
TPS65800RTQT 功能描述:电池管理 1-Cell L-Ion Battery & Pwr Mngmnt IC RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel
TPS65800RTQT 制造商:Texas Instruments 功能描述:POWER M SGL C LI ION 3~18V 56QFN 制造商:Texas Instruments 功能描述:POWER M, SGL C LI ION, 3~18V, 56QFN