参数资料
型号: TPS72525DCQ
厂商: Texas Instruments, Inc.
英文描述: LOW INPUT VOLTAGE, 1-A LOW-DROPOUT LINEAR REGULATORS WITH SUPERVISOR
中文描述: 低输入电压,1低压差线性稳压器与督导员
文件页数: 18/18页
文件大小: 535K
代理商: TPS72525DCQ
www.ti.com
APPLICATION INFORMATION
External Capacitor Requirements
Programming the TPS72501 Adjustable LDO Regulator
V
O +
V
ref
1 )
R1
R2
(1)
R1 +
V
O
V
ref
* 1
R2
(2)
VO
VI
OUT
FB
R1
R2
GND
EN
IN
TPS72501
1
F
Co
OUTPUT VOLTAGE
PROGRAMMING GUIDE
(Standard 1% Resistor Values)
PROGRAM
VOLTAGE
R1 (K
) R2 (k)
1.8 V
2.5 V
3.3 V
3.6 V
ACTUAL
VOLTAGE
56.2
127
196
205
118
121
115
105
1.801
2.500
3.299
3.602
1.22 V
≤ 0.4 V
≥ 1.3 V
TPS72501
TPS72515, TPS72516
TPS72518, TPS72525
SLVS341D – MAY 2002 – REVISED MARCH 2004
The TPS725xx family of low-dropout (LDO) regulators has numerous features that make it applicable to a wide
range of applications. The family operates with very low input voltage (
≥1.8 V) and low dropout voltage (typically
200 mV at full load), making it an efficient stand-alone power supply or post regulator for battery or switch mode
power supplies. Both the active low RESET and 1-A output current make the TPS725xx family ideal for powering
processor and FPGA supplies. The TPS725xx family also has low output noise (typically 150 VRMS with 10-F
output capacitor), making it ideal for use in telecom equipment.
A 1-F or larger ceramic input bypass capacitor, connected between IN and GND and located close to the
TPS725xx, is required for stability. To improve transient response, noise rejection, and ripple rejection, an
additional 10-F or larger, low ESR capacitor is recommended. A higher-value, low ESR input capacitor may be
necessary if large, fast-rise-time load transients are anticipated and the device is located several inches from the
power source, especially if the minimum input voltage of 1.8 V is used.
Although an output capacitor is not required for stability, transient response and output noise are improved with a
10-F output capacitor.
The output voltage of the TPS72501 adjustable regulator is programmed using an external resistor divider as
shown in Figure 19. The output voltage is calculated using:
Where:
VFB = VREF = 1.22 V typical (see the electrical characteristics for VREF range)
Resistors R1 and R2 should be chosen for approximately 10-A divider current. Lower value resistors offer no
inherent advantage and waste more power. Higher values should be avoided as leakage currents at FB increase
the output voltage error. The recommended design procedure is to choose R2 = 120 k
to set the divider current
at 10 A and then calculate R1 using:
Figure 19. TPS72501 Adjustable LDO Regulator Programming
9
相关PDF资料
PDF描述
TPS72525KTT LOW INPUT VOLTAGE, 1-A LOW-DROPOUT LINEAR REGULATORS WITH SUPERVISOR
TPS726126 "Single Output LDO
TPS726126DCQ LOW INPUT VOLTAGE, 1-A LOW-DROPOUT LINEAR REGULATORS WITH SUPERVISOR
TPS726126DCQR LOW INPUT VOLTAGE, 1-A LOW-DROPOUT LINEAR REGULATORS WITH SUPERVISOR
TPS72615KTTR LOW INPUT VOLTAGE, 1-A LOW-DROPOUT LINEAR REGULATORS WITH SUPERVISOR
相关代理商/技术参数
参数描述
TPS72525DCQ 制造商:Texas Instruments 功能描述:V REG LDO SMD 72525 SOT-223-6
TPS72525DCQG4 功能描述:低压差稳压器 - LDO Low Input Voltage Any Cap 1-A RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压(最大值):307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20
TPS72525DCQR 功能描述:低压差稳压器 - LDO Low Input Voltage Any Cap 1-A RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压(最大值):307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20
TPS72525DCQRG4 功能描述:低压差稳压器 - LDO Low Input Voltage Any Cap 1-A RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压(最大值):307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20
TPS72525KTT 制造商:Rochester Electronics LLC 功能描述:LOW DROP-OUT REGULATOR - Tape and Reel 制造商:Texas Instruments 功能描述: