参数资料
型号: TS12A4516P
厂商: TEXAS INSTRUMENTS INC
元件分类: 多路复用及模拟开关
英文描述: 1-CHANNEL, SGL POLE SGL THROW SWITCH, PDIP8
封装: PLASTIC, DIP-8
文件页数: 11/13页
文件大小: 404K
代理商: TS12A4516P
www.ti.com
APPLICATION INFORMATION
Power-Supply Considerations
Logic-Level Thresholds
Test Circuits/Timing Diagrams
NO
orNC
DUAL SUPPLY, LOW ON-STATE RESISTANCE
SPST CMOS ANALOG SWITCHES
SCDS236A – DECEMBER 2006 – REVISED MARCH 2007
The TS12A4516 and TS12A4517 operate with power-supply voltages from
±1 V to ±6 V [(2 V < (V
+ – V) <
12 V], but are tested and specified at
±5V, ±3.3V, and ±1.8V supplies. The pin-compatible TS12A4514 and
TS12A4515 are recommended for use when only a single supply is desirable.
The TS12A4516 and TS12A4517 construction is typical of most CMOS analog switches, except that they have
only two supply pins: V+ and V. V+ and Vdrive the internal CMOS switches and set their analog voltage limits.
Reverse ESD-protection diodes are internally connected between each analog-signal pin and both V+ and V.
One of these diodes conducts if any analog signal exceeds V+ or V.
Virtually all the analog leakage current comes from the ESD diodes to V+ or V. Although the ESD diodes on a
given signal pin are identical and, therefore, fairly well balanced, they are reverse biased differently. Each is
biased by either V+ or Vand the analog signal. This means their leakages will vary as the signal varies. The
difference in the two diode leakages to the V+ and Vpins constitutes the analog-signal-path leakage current. All
analog leakage current flows between each pin and one of the supply terminals, not to the other switch terminal.
This is why both sides of a given switch can show leakage currents of the same or opposite polarity.
There is no connection between the analog-signal paths and V+ or V.
V+ and Valso power the internal logic and logic-level translators. The logic-level translators convert the logic
levels to switched V+ and Vsignals to drive the analog signal gates.
The logic-level thresholds are CMOS compatible but not TTL compatible. As V+ is raised, the level threshold
increases slightly. When V+ reaches 12 V, the level threshold is about 3 Vabove the TTL-specified high-level
minimum of 2.8 V, but still compatible with CMOS outputs.
CAUTION:
Do not connect the TS12A4516/TS12A4517 V+ to 3 V and then connect the
logic-level pins to logic-level signals that operate from 5-V supply. TTL levels
can exceed 3 V and violate the absolute maximum ratings, damaging the part
and/or external circuits.
Figure 1. Charge Injection
7
相关PDF资料
PDF描述
TS2007EIJT 3 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA9
TS2007EKIJT 3 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA9
TS2007IQT 2.3 W, 1 CHANNEL, AUDIO AMPLIFIER, DSO8
TS2012EIJT 2.5 W, 2 CHANNEL, AUDIO AMPLIFIER, PBGA16
TS2012IQT 2.8 W, 2 CHANNEL, AUDIO AMPLIFIER, PQCC20
相关代理商/技术参数
参数描述
TS12A4517 制造商:TI 制造商全称:Texas Instruments 功能描述:DUAL SUPPLY, LOW ON-STATE RESISTANCE SPST CMOS ANALOG SWITCHES
TS12A4517D 功能描述:模拟开关 IC Lo-Vltg Lo On-St Resist SPST CMOS RoHS:否 制造商:Texas Instruments 开关数量:2 开关配置:SPDT 开启电阻(最大值):0.1 Ohms 切换电压(最大): 开启时间(最大值): 关闭时间(最大值): 工作电源电压:2.7 V to 4.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-16
TS12A4517DBVR 功能描述:模拟开关 IC Lo-Vltg Lo On-State Res SPST CMOS Ana Sw RoHS:否 制造商:Texas Instruments 开关数量:2 开关配置:SPDT 开启电阻(最大值):0.1 Ohms 切换电压(最大): 开启时间(最大值): 关闭时间(最大值): 工作电源电压:2.7 V to 4.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-16
TS12A4517DG4 功能描述:模拟开关 IC Lo-Vltg Lo On-St Resist SPST CMOS RoHS:否 制造商:Texas Instruments 开关数量:2 开关配置:SPDT 开启电阻(最大值):0.1 Ohms 切换电压(最大): 开启时间(最大值): 关闭时间(最大值): 工作电源电压:2.7 V to 4.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-16
TS12A4517DR 功能描述:模拟开关 IC Lo-Vltg Lo On-St Resist SPST CMOS RoHS:否 制造商:Texas Instruments 开关数量:2 开关配置:SPDT 开启电阻(最大值):0.1 Ohms 切换电压(最大): 开启时间(最大值): 关闭时间(最大值): 工作电源电压:2.7 V to 4.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-16