- 您现在的位置：买卖IC网 > PDF目录373695 > TS1581CZ5 (Taiwan Semiconductor Co., Ltd.) 5.0 AMP POSITIVE VOLTAGE REGULATOR PDF资料下载
参数资料
| 型号： | TS1581CZ5 |
| 厂商： | Taiwan Semiconductor Co., Ltd. |
| 元件分类： | 基准电压源/电流源 |
| 英文描述： | 5.0 AMP POSITIVE VOLTAGE REGULATOR |
| 中文描述： | 5.0放大器正电压稳压器 |
| 文件页数： | 6/7页 |
| 文件大小： | 135K |
| 代理商： | TS1581CZ5 |
TS1581 series
6-6
2003/12 rev. B
Application Information (continued)
Protection Diodes
In normal operation TS1581 family does not need any
protection diodes between the Adjust pin and the
output and from the output to the input to prevent die
overstress. Internal resistors are limiting the internal
current paths on the Adjust pin. Therefore even with
bypass capacitors on the Adjust pin no protection diode
is needed to ensure device safety under short-circuit
conditions. The Adjust pin can be driver on a transient
basis +/-7V with respect to the output without any
device degradation.
A protection diode between the Output pin and Vpower
pin is not usually needed. Microsecond surge currents
of 50A to 100A can be handled by the internal diode
between the Output pin and Vpower pin of the device.
In normal operations it is difficult to get those values of
surge currents even with the use of large output
capacitances. Only with high value output capacitors,
such as 1000uF to 5000uF and the Vpower pin is
instantaneously shorted to ground, damage can occur.
A diode from output to input is recommended.
Figure 6. Optional Clamp Diodes Protect Against Input
Crowbar Circuits
If TS1581 is connected as a single supply device with
the control and power input ins shorted together the
internal diode between the output and the power input
pin will protect the control input pin.
Thermal Considerations
The TS1581 family have internal power and thermal
limiting circuit designed to protect the device under
overload conditions. However maximum junction
temperature ratings should not be exceeded under
continuous
normal
load
consideration must be given to all sources of thermal
resistance from junction to ambient,
conditions.
Careful
including junction-to-case, case-to-heat sink interface
and heat sink resistance itself. Junction temperature of
the Control section can urn up to125
o
C. Junction
temperature of the Power section can run up to 150
o
C.
Due to the thermal gradients between the power
transistor and the control circuitry there is a significant
difference in thermal resistance between the Control
and Power sections.
Virtually all the power dissipated by the device is
dissipated in the power transistor. The temperature rise
in the power transistor will be greater than the
temperature rise in the Control section making the
thermal resistance lower in the Control section. At
power levels below 12W the temperature gradient will
be less than 25
o
C and the maximum ambient
temperature will be determined by the junction
temperature of the Control section. This is due to the
lower maximum junction temperature in the Control
section. At power levels above 12W the temperature
gradient will be greater than 25
o
C and the maximum
ambient temperature will be determined by the Power
section. In both cases the junction temperature is
determined by the total power dissipated in the device.
For most low dropout applications the power dissipation
will be less than 12W.
The power in the device is made up of two
components: the power in the output transistor and the
power in the control circuit.
The power in the control circuit is negligible.
The power in the control circuit is equal to:
Pcontrol = ( Vcontrol – Vout ) ( Icontrol )
Where Icontrol is equal Iout / 100 (typ)
The power in the out transistor is equal to:
Poutput = ( Vpower – Vout ) ( Iout )
The total power is equal to:
Ptotal = Pcontrol + Poutput
Junction-to-case thermal resistances is specified from
the IC junction to the bottom of the case directly below
the die. This is the lowest resistance path for the heat
flow. In order to ensure the best possible thermal flow
this area of the package to the heat sink proper
mounting is required. Thermal compound at the
case-to-heat sink interface is recommended. A
thermally conductive spacer can be used, if the case of
the device must be electrically isolated, but its added
contribution to thermal resistance has to be considered.
相关PDF资料 |
PDF描述 |
|---|---|
| TS1581CZ525 | 5.0 AMP POSITIVE VOLTAGE REGULATOR |
| TS1581 | 5.0 AMP POSITIVE VOLTAGE REGULATOR |
| TS1581CM5 | 5.0 AMP POSITIVE VOLTAGE REGULATOR |
| TS1581CM525 | D-Subminiature Connector; Gender:Female; Number of Contacts:9; Contact Termination:Crimp; Body Material:Steel; Contact Plating:Gold |
| TS1581CM533 | 5.0 AMP POSITIVE VOLTAGE REGULATOR |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TS1581CZ52.5 | 制造商:TSC 制造商全称:Taiwan Semiconductor Company, Ltd 功能描述:5A Dual Input Low Dropout Positive Voltage Regulator |
| TS1581CZ525 | 制造商:TSC 制造商全称:Taiwan Semiconductor Company, Ltd 功能描述:5A Dual Input Low Dropout Positive Voltage Regulator |
| TS1581CZ53.3 | 制造商:TSC 制造商全称:Taiwan Semiconductor Company, Ltd 功能描述:5A Dual Input Low Dropout Positive Voltage Regulator |
| TS1581CZ533 | 制造商:TSC 制造商全称:Taiwan Semiconductor Company, Ltd 功能描述:5A Dual Input Low Dropout Positive Voltage Regulator |
| TS1581CZ5C0 | 制造商:TSC 制造商全称:Taiwan Semiconductor Company, Ltd 功能描述:5A Dual Input LDO |
发布紧急采购，3分钟左右您将得到回复。