- 您现在的位置：买卖IC网 > PDF目录97770 > TS2596CM50RN SWITCHING REGULATOR, 173 kHz SWITCHING FREQ-MAX, PSSO5 PDF资料下载
参数资料
| 型号： | TS2596CM50RN |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING REGULATOR, 173 kHz SWITCHING FREQ-MAX, PSSO5 |
| 封装： | ROHS COMPLIANT, TO-263, D2PAK-5 |
| 文件页数： | 5/8页 |
| 文件大小： | 397K |
| 代理商： | TS2596CM50RN |
TS2596
3A / 150KHz Buck Dc-Dc Converter
5/8
Version: B07
Pin Function Description
Vcc
This is the positive input supply for the IC switching regulator. A suitable input bypass capacitor must be presented at
this pin to minimize voltage transients and to supply the switching currents needed by the regulator.
Ground
Circuit ground
SW Output
Internal switch. The voltage at this pin switches between (+Vcc – Vsat) and approximately – 0.5V, with a duty cycle of
approximately Vout / Vcc. To minimize coupling to sensitive circuitry, the PC board copper area connected to this pin
should be minimized.
Feedback
Sense the regulated output voltage to complete the feedback loop.
Enable
Allows the switching regulator circuit to be shutdown using logic level signals thus dropping the total input supply
current to approximately 100uA. Pulling this pin below a threshold voltage of approximately 1.3V turns the regulator on,
and pulling this pin above 1.3V (up to a maximum of Vcc) shuts the regulator down. If this shutdown feature is not
needed, the EN pin can be wired to the ground pin.
Thermal Considerations
The TS2596 is available in two packages, a TO-220-5L and TO-263-5L.
The TO-220-5L package needs a heat sink under most conditions. The size of the heat sink depends on the input
voltage, the output voltage, the load current and the ambient temperature. The TS2596 junction temperature rises
above ambient temperature for a 3A load and different input and output voltages. The data for these curves was taken
with the TS2596 (TO-220-5L package) operating as a buck switching regulator in an ambient temperature of 25
o
C (still
air). These temperature rise numbers are all approximate and there are many factors that can affect these
temperatures. Higher ambient temperatures require more heat sinking.
The TO-263-5L surface mount package tab is designed to be soldered to the copper on a printed circuit board. The
copper and the board are the heat sink for this package and the other heat producing components, such as the catch
diode and inductor. The PC board copper area that the package is soldered to should be at least 0.8 in
2
, and ideally
should have 2 or more square inches of 2 oz. Additional copper area improves the thermal characteristics, but with
copper areas greater than approximately 6 in
2
, only small improvements in heat dissipation are realized. If further
thermal improvements are needed, double sided, multilayer PC board with large copper areas and/or airflow are
recommended.
The TS2596 (TO-263-5L package) junction temperature rise above ambient temperature with a 3A load for various
input and output voltages. This data was taken with the circuit operating as a buck switching regulator with all
components mounted on a PC board to simulate the junction temperature under actual operating conditions. This
curve can be used for a quick check for the approximate junction temperature for various conditions, but be aware that
there are many factors that can affect the junction temperature. When load currents higher than 3A are used, double
sided or multilayer PC boards with large copper areas and/or airflow might be needed, especially for high ambient
temperatures and high output voltages.
For the best thermal performance, wide copper traces and generous amounts of printed circuit board copper should be
used in the board layout. (Once exception to this is the output (switch) pin, which should not have large areas of
copper.) Large areas of copper provide the best transfer of heat (lower thermal resistance) to the surrounding air, and
moving air lowers the thermal resistance even further.
相关PDF资料 |
PDF描述 |
|---|---|
| TS3-73BA1 | 1 FUNCTIONS, 73.35 MHz, 6.5 kHz BW(delta f), MONOLITHIC CRYSTAL FILTER |
| TS4-73BA2 | 1 FUNCTIONS, 73.35 MHz, 7.5 kHz BW(delta f), MONOLITHIC CRYSTAL FILTER |
| TS3410CX5RF | 1.4 A SWITCHING REGULATOR, 1700 kHz SWITCHING FREQ-MAX, PDSO5 |
| TS3431ILT | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 1.24 V, PDSO3 |
| TS3V555ID | PULSE; RECTANGULAR, 2 MHz, TIMER, PDSO8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TS2596CM512 RN | 制造商:SKMI/Taiwan 功能描述:TO-263-5L;3AMP STEP DOWN 12V S |
| TS2596CM53.3 | 制造商:TSC 制造商全称:Taiwan Semiconductor Company, Ltd 功能描述:3A Step Down Switching Voltage Regulator |
| TS2596CM533 | 功能描述:开关变换器、稳压器与控制器 3.3V 3.0A RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| TS2596CM533 RN | 制造商:SKMI/Taiwan 功能描述:3A / 150KHZ BUCK DC-DC CONVERTER |
| TS2596CM55 | 制造商:TSC 制造商全称:Taiwan Semiconductor Company, Ltd 功能描述:3A Step Down Switching Voltage Regulator |
发布紧急采购，3分钟左右您将得到回复。